User manual ELECTRO-VOICE PSX2200
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE PSX2200. We hope that this ELECTRO-VOICE PSX2200 user guide will be useful to you.
Lastmanuals help download the user guide ELECTRO-VOICE PSX2200.
Manual abstract: user guide ELECTRO-VOICE PSX2200
Detailed instructions for use are in the User's Guide.
[. . . ] STEREO POWERED MIXER PSX1000 PSX1600 PSX2200
Introduction . Standard installation + Master patchbay and installation alternatives . 3 4 8 10 12 13 14 18 19 26 27 28 32
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance (servicing) instructions in the literature accompanying the appliance.
1. [. . . ] AUX/FX SEND
These rotary controls could also be called FX SEND master controls, since they are used to adjust the overall level of the effect mix that you have established using the channel FX send controls. The AUX/FX SEND controls are used to set the input levels of the corresponding FX unit, respectively and the levels of the AUX SEND outputs. Whenever the Peak LED (PK) blinks, there is the potential risk that the FX input signal is driven into clipping, making it necessary to reduce its level by turning the corresponding AUX/FX SEND control to the left, until the LED is not lit anymore. Since the AUX/FX SEND controls not only affect the signals of the FX buses but also the monitor effect level, which is sent by the FX to AUX3 control, careless changes can result in acoustical feedback.
10 of 32
30. FX ON
These switches are used to turn the internal FX units on the green LED is lit. Please keep in mind that you also can use an external foot switch to turn the FX units on. If you want to use a foot switch, the FX ON switch has to be engaged first. The corresponding FX unit is activated and you can use the foot switch to turn the selected effect program on or off.
31. PEAK LED
These indicators show if the input stages of the internal FX units or the AUX 1/" SEND signals are driven into clipping. To achieve an adequate S/N ratio, please adjust the FX units' input level as follows: Note on how to adjust the FX input signal: 1. Establish a "dry" mix without effect settings according to the previous descriptions. Set the AUX/FX send controls of the effect channels to their center position. Position the effect return faders of the effect channels at the 5dB marks. Play the sound source of the desired input channel and adjust the desired amount of the FX signal, using the AUX/FX controls of this input channel. Repeat this step for all input channels that you want to include in your effect mix. Adjust the AUX/FX SEND controls, so that the Peak LED only lights frequently at highly dynamic signal peaks. Use the FX return faders to add the desired amount of the FX signal to the main mix. In case you are using a different effect setting for the second FX unit, you have to repeat the step 2 - 8, respectively. Pay some attention to the peak indicators when operating your PSX to quickly interact when the signal levels exceed the normal range and enter clipping.
32. EFFECT RETURN
These stereo faders are used to determine the effect amount of the main mix. In case you have to set these faders at a position above the +5dB mark, please check if the FX units input signals are adjusted properly. Otherwise use the AUX/FX SEND controls to increase the input levels.
11 of 32
Typically, the AUX3 channel is used as monitor bus. [. . . ] An active cross-over is connected to the MAIN OUTPUTS or the EQ OUTPUTS which carry the full-range signals. The LF-signal outputs of the crossover are connected to an external power amplifier, driving the woofer cabinets. The signal of the crossover's HF-signal outputs is fed into the PSX's internal power amplifier via the POWER AMP INPUTS. Compared to the passive configuration, the overall sound gains clarity and higher volume levels are possible, since the Hi/Mid cabinets do not have to deal with the low frequency signals.
25 of 32
Technical Specifications PSX Mixing desk in rated condition, Unity Gain ( MIC Gain 20 dB ), all faders position 0 dB, all pots in mid position, Master fader + 6dB, amplifier rated output power into 8 ohms, one channel driven, unless otherwise specified. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE PSX2200
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE PSX2200 will begin.