User manual ELECTRO-VOICE R200

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE R200. We hope that this ELECTRO-VOICE R200 user guide will be useful to you.

Lastmanuals help download the user guide ELECTRO-VOICE R200.


ELECTRO-VOICE R200 : Download the complete user guide (1028 Ko)

Manual abstract: user guide ELECTRO-VOICE R200

Detailed instructions for use are in the User's Guide.

[. . . ] 9 page 2 R200 OWNERS MANUAL R200 SERIES OWNER'S MANUAL System Features True-diversity system with Secure-Phasetm ensures maximum range and freedom from interference Well-designed companding and audio circuitry insure high signal-to-noise ratio and excellent sound quality Choice of handheld, bodypack, lavalier, headset and guitar systems Permanently attached antennas make setup quick and easy. Audio output via 3-pin XLR-type balanced mic level and ¼-inch unbalanced line level connectors Designed and manufactured in the United States of America DESCRIPTION The Electro-Voice R200 is a series of UHF wireless systems that combine EVs legendary quality, reliability and high value. The R200 Series transmitters and receivers operate in the UHF frequency range between 710. 100 and 721. 350 MHz (channels 54-55 in the TV band) on single frequencies. The well-designed audio circuitry ensures excellent signal-to-noise ratio with accurate sound quality. [. . . ] If the audio becomes distorted, turn the mic level control counter-clockwise about 1/8 turn. The squelch control on the back of the receiver may be adjusted to increase range or reduce interference. Turn the control counter- R200 OWNERS MANUAL clockwise to increase range. Increasing the range will make the system more susceptible to outside interference!Turn the squelch control counter-clockwise until you hear noise or interference. Then, turn the squelch clockwise until the noise is gone. BODYPACK TRANSMITTER SETUP 1. Open the hinged battery compartment by placing your thumb or finger on the indent on the battery door and pull down. When inserting the battery, pay attention to the polarity (+/-) and insert the terminals into the battery compartment first. Turn on the transmitter by sliding the power switch to its on position. Check the condition of the battery by looking at the LED below the power switch. Prepare the audio source by attaching the lavalier microphone to the user, placing the headset on the users head or plugging the cable into the instrument (depending on what type of system you have). Keep the audio muted while plugging in and adjusting the microphone or source. Placement of lavalier and headset microphones will noticeably change the sound quality, so some experimentation with the user is necessary. B E LT CL IP M AY B E TU R NE D 90 D E G RE E S BY RE M O V ING S C R E W A N D R EIN STA LLIN G HERE. 4. Check reception by observing that the RF carrier light is illuminated on the receivers front panel. Turn on the audio transmission by sliding the large mute switch to the on position. Listen carefully to the audio and be sensitive of overload distortion and low gain or hiss. (2. 5 mm) screwdriver into the gain adjustment located at the top edge of the battery compartment under the door. Turn lightly until the screwdriver tip drops into the slot on the level control. Gently turn the control counterclockwise until the control stops (the audio output is attenuated but not off). Slowly turn the audio level control clockwise while listening to audio; if the audio becomes distorted, turn the mic level control counter-clockwise about 1/8 turn. The bodypack can be positioned horizontally or vertically by moving the belt clip attachment. Removing the belt clip attachment screw and moving it 90 degrees will change the orientation. G AIN A DJU S TM E NT DOOR OPENED B UT N O T S W U N G UP WA RD POW ER S W ITC H AU D IO S W ITC H M IC O R G UITA R CA B LE E NTRY P OW ER S W IN G D O O R U P WA R D TO A CC ES S B ATTE RY C O M PA R TM EN T TO O P E N BATTE RY D O O R P R E S S A R RO W W ITH IN D E X FIN G E R AN D P UL L D O W N W ITH TH U M B A N D M IDD LE FIN G E R AUD IO ON ON BATTE RY LIG HT page 5 R200 OWNERS MANUAL COMPATIBILITY The receiver and transmitter must be on the same UHF frequency to operate together. [. . . ] Many rf-reflective metal obstacles between the transmitter and receiver. Return to factory or authorized service station. Move the obstacles or reposition the receiver. page 9 R200 OWNERS MANUAL INSTALATION FOR RECEIVER RACK MOUNT KIT R-Series wireless receivers can be rack mounted with the optional RMR kit. The RMR allows two receivers to be mounted side-by-side in a single rack space. Fold antennas down and insert the R-Series receiver through the rectangular cut-out as shown. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE R200

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE R200 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag