User manual ELECTRO-VOICE TCA-1
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ELECTRO-VOICE TCA-1. We hope that this ELECTRO-VOICE TCA-1 user guide will be useful to you.
Lastmanuals help download the user guide ELECTRO-VOICE TCA-1.
Manual abstract: user guide ELECTRO-VOICE TCA-1
Detailed instructions for use are in the User's Guide.
[. . . ] Truss Mount Kits User Instructions
The Electro-Voice® TMK Truss Mount Kits are accessories that are designed to suspend Electro-Voice loudspeakers to a truss. [. . . ] The upper point is used for 12" Loudspeakers and the lower point is used for 15" Loudspeakers (see Figure 3). *Note: For ZX Series loudspeakers, attach the HA-3 or HA-5 adaptor to the loudspeaker before proceeding.
Attachment Point for all 12" Loudspeakers
Top of Assembly
Attachment Point for all 15" Loudspeakers Bottom of Assembly
Figure 3: Adjusting the Loudspeaker Attachment Point on the VSA-1
Installing the HA-3 or HA-5 (ZX-Series Loudspeakers Only)
Remove the M10 bolts that secure the handle to the loudspeaker, and fasten the HA-3 or HA-5 bracket in its place (see Figure 4).
Figure 4a: Removing the Bolts Securing the Handle
Figure 4b: Attaching the HA-3 or HA-5 to the ZX Loudspeaker
Figure 4c: Attaching the VSA-1 to the HA-3 or HA-5 Handle Adaptor
Attaching VSA-1 to Loudspeaker (all Speakers)
Thread the VSA-1 to the loudspeaker by using the threaded bracket (PX1122M, PX1152M, Plasma P1) or HA-3 or HA-5 adaptor (ZX Series) on the right side of the enclosure. Rotate the loudspeaker to the desired vertical tilt position, and torque the threaded stud to the enclosure using the handle (see Figure 5).
Optional: If local regulations require an additional safety point, attach an M10 shoulder eyebolt (not included) to this point on the VSA-1. See Page 4 for required safety points.
WARNING: The rubber pad acts as a locking mechanism for the threaded shaft. If enough torque is not applied to the handle, vibrations from the loudspeaker may loosen the shaft over time. The user should regularly inspect the shaft to ensure that the VSA-1 has not loosened from the loudspeaker.
Figure 5a: Tightening the Attachment Point on the VSA-1 to a PX-Series Loudspeaker
Figure 5b: Tightening the Attachment Point on the VSA-1 to a ZX-Series Loudspeaker
Attaching Truss Mount and Speaker Assembly to Truss (all Speakers)
Loosen the clamping fixture on the TCA-1 and open the clamp. Attach the TCA-1 (including the strong arm and loudspeaker) to the truss by sliding it past the clamping fixture. Adjust the clamp so it is behind the clamping fixture, and tighten the handle (see Figure 6).
Loosening Step 2 Open Clamp
Clamping Step 1 Close Clamp
Loosening Step 1 Loosen T-Handle
Clamping Step 2 Tighten T-Handle
Figure 6a: Loosening Clamping Feature on Truss Mount
Figure 6b: Attaching Truss Mount and Loudspeaker Assembly to Truss
Attaching Safety Point to Speaker (PX1122M and PX1152M)
For PX1122M and PX1152M Only: Remove the M10 flat head bolt from the loudspeaker, and replace with a forged steel shoulder eyebolt with a minimum safe working load of 100 lbs. [. . . ] For customer orders, Contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 887-9212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ELECTRO-VOICE TCA-1
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ELECTRO-VOICE TCA-1 will begin.