User manual ELK PRODUCTS ELK-106055

[. . . ] ENROLLING PROX CARDS AND FOBS WITH M1 CONTROL Each prox card/fob must be enrolled into a User Code location, using the same procedures that are used to add/change User Code PINs. On the Keypad, press the center ELK key. Press 6 to jump directly to Menu 06 - Change User Codes OR Use the UP or DOWN arrow keys to scroll to the menu. [. . . ] If the keypad accepts the new prox card/fob, it will beep 3 times and display a 12 digit code, which is part of the ID stored in the card/fob. If the keypad rejects the prox card/fob, it will produce a low error tone and display: Code Not Authorized, Redo The reject error may be caused by: A. The card or fob has already been enrolled (the M1 does not allow duplicate codes) OR B. The facility code stored in the prox card/fob does not match the ELK facility code. The UltraProx Weigand Reader can only read cards/fobs which have the matching facility code. After a prox card/fob has been enrolled into a user code location, its capabilities are set by the User Code Options found in Menu 02 of the M1 Installer Level Programming. The most common of these options are: - Arm the M1 Control. - Access - Trip output to de-energize a lock ** ** The activation assignment for M1 Outputs requires the Whenever/And/Then Rules programming of the Elk-RP Software. UltraProx Weigand Reader ELK-106055 APPLICATION: The Elk UltraProx Weigand Reader is a compact, technically advanced external proximity reader with 26 bit Weigand output for use with most access controllers and the Elk M1 control family. It is ideal for higher security installations and as an alternative to remembering PIN codes. TM UltraProx Weigand Reader ELK-106055 FEATURES: · · · · · · · · Compatible with ELK M1 control family Compatible with most access controllers 26-bit Weigand Output Slimline waterproof housing with epoxy potted electronics User configurable inputs for the onboard buzzer and green LED Compatible with Clamshell Style (Credit Card size) Proximity Cards (ELK-M1PRC) Compatible with Keychain Style Proximity Fobs (ELK-M1PRF) Substitutes for User Code Pin Entry SPECIFICATIONS: · · · · · Reader Format: 26 bit Weigand Nominal Read Range: ~ 3" Operating Voltage: 12 VDC Current Draw: 50 mA. Size: 1. 9 W x 3. 2" H x . 9" D Features or Specifications subject to change without notice. CARDS AND FOBS (ordered separately) ELK-M1PRC Prox Cards The following example is a rule to activate Output 003 for 10 seconds when a valid prox card/fob (with Access Option enabled) is presented at Keypad 01. The output could be used to break or make power to a door strike. WHENEVER Keypad 01 Access is Activated THEN Turn On Output 003 for 10 seconds. · Pack of 10, White clam shell style card · Size: 2 1/8" L x 3 3/8" H x 3/16" T ELK-M1PRF Prox Fobs · Pack of 10, Black keyring fobs · Size: 2 1/8" L x 1 1/4" H x 1/4" T 828-397-4200 Voice 828-397-4415 Fax http://www. elkproducts. com email: info@elkproducts. com PO Box 100 · Hwy. 70W · Hildebran, NC 28637 · USA 03/06 Installation Instructions on Inside INSTALLATION The reader is designed for surface mounting adjacent to the door being controlled. The unit is fully sealed for indoor or outdoor use. [. . . ] Plug the W035A cable into connector J2 6. Reconnect the 6 pin data bus cable to connector J1 and install the keypad onto its mounting plate. Refer to the instructions for enrolling cards or fobs. Figure 1 Brown Green Black White Red Figure 2 ELK-M1KP LCD Keypad Back (Circuit) Side of Keypad ELK-WO35A Cable Assembly (not included) Maximum Wire Distance = 10 ft. ELK-106055 UltraProx Reader (26 bit Wiegand) J2 Connector Six (6) conductor plug-in data bus cable J1 To Proximity Reader Red White Black Green Brown Wire Insulate (No Connection) Blue Violet Insulate Brown (No Connection) Shield } [. . . ]