User manual ELK PRODUCTS ELK-ML8

[. . . ] * Try these other fine ELK products * M1 Cross Platform Control M1 (Std) Integrates Security, Lighting, Telephone, and Energy Management. Powerful "Rules" based automation capabilities. M1G (Gold) More powerful version of M1 with more expansion and capabilities. [. . . ] · Real Time Clock & Calendar Event Functions utilizing the Caddx NX built-in clock. · Small Size Conveniently Mounts inside Control. · Lifetime Limited Warranty, call for details. SPECIFICATIONS: · Size: 4" x 2. 75" (102mm x 70mm). · Operating Power Derived From the Magic Module Power Source or the Caddx Control. · Operating Voltage: 9. 6-15 Volts D. C. · Current Required: 30mA. REQUIRED EQUIPMENT: (not included) · ELK Magic Module (ELK-MM443). · ELK Programming Kit (ELK-MK485). Features and Specifications subject to change without notice. 828-397-4200 Voice 828-397-4415 Fax http://www. elkproducts. com email: info@elkproducts. com PO Box 100 · Hwy. 70W · Hildebran, NC 28637 · USA Instructions Printed On Inside The Link Interface (ELK-ML8) connects to the data bus of the Caddx NX Control¹ using only 2 wires. Data received from the control is mapped to 16 collection flags. Changes to these flags are broadcasted over the Magic Module data bus. In addition, 240 bits of data from the Control may be interrogated on demand by the Magic Module. In order to program the 16 collection flags or develop a Home Control or Automation application, a Magic Module Programmers Kit (ELK-MK485) is needed. INSTALLATION Step 1. Disconnect all power to the Caddx NX Security Control and the ELK Magic Module. Mount the Link Interface using the enclosed self adhesive foam tape or two of the special NX enclosure slide rails. Connect the Link Interface, Caddx NX Control, and Magic Module as per figure 1 below. [. . . ] The Software includes a manual and on-line help screens. XMIT RCV STATUS PWR = = = = Blinks when information is being transmitted to or received from a Magic Module Blinks when the NX Control is transmitting information to the Link Interface Blinks slowly when the Control Keypad data bus is operational. On when the Link Interface is receiving Power. LEDs ¹ Works with most Caddx NX Controls except "E" series * CADDX NX4/6/8 ALARM CONTROL LINK INTERFACE ELK-ML8 JP1 MODE Leave in the NORMAL Position D5 not used Mount the ELK-ML8 Interface Here Or Mount using Rails Here DATA NEG +V AUX NORMAL +12V A B NEG J1 XMIT RCV STATUS PWR +V NEG DATA TO CADDX KEYPAD BUS (3 WIRES) RED GREEN RS-485 BUS (4 WIRES) BLACK YELLOW See Step 3 for +V Optional Hookup NEG B DATA A DATA +12 VOLTS KP DATA KP COM KP POS CADDX NX ALARM CONTROL BOARD * ELK-MM443 MAGIC MODULE 1 2 4 8 16 J1 SELECT X-10 2-WAY 1-WAY JP10 POWER J3 X-10 and DALLAS Interface J5 RELAY 4 IN OUT RELAY 3 IN OUT * OPTIONAL POWER SUPPLY ELK-P1216 DATA BUS ADDRESS JUMPERS SET TO ADDRESS 1 JP1 JP2 JP3 JP4 K1 K2 K3 K4 + AB J2 1 See Step 3 for +V Optional Hookup - 2 3 - 4 NO COM NCNO COM NCNOCOM NCNO COM NC RELAY 3 RELAY 4 RELAY 1 RELAY 2 * X-10 Items noted with * must be purchased separately 2 WAY POWERLINE INTERFACE MODEL:PSC05 Required only for Applications using X-10 Devices Figure 1. [. . . ]