User manual ELK PRODUCTS ELK-PD9(HC)

[. . . ] Power Distribution Modules ELK-PD9 250mA rated outputs ELK-PD9HC 400mA rated outputs These Power Distribution Modules conveniently distribute a single A. C. input into nine individual outputs, for centrally powering Video Cameras, PIRs, Photobeams, etc. Each output is protected with an auto-resetting PTC to protect a shorted output from disabling the other outputs. [. . . ] · Input Connection: Screw Terminals or 2. 1mm Plug-In D. C. · Output Connection: Screw Terminals (POS and NEG) for each Output. · Enclosure Size: 6. 5" x 4. 3" x 2". Kit Part Numbers PD9AC24 AC Camera Kit: Includes ELK-PD9 + ELK-TRG2440 24V AC, 40VA Transformer. PD9DC12 DC Camera Kit: Includes ELK-PD9 + ELK-P1216 12V DC, 1. 5A Plug-in Power Supply. PO Box 100 · Hildebran, NC 28637 · 800-797-9355 · 828-397-4200 Fax 828-397-4415 · www. elkproducts. com · info@elkproducts. com ELK PRODUCTS, INC. Instructions ELK-PD9 1. To remove the cover from the Power Distribution Module (ELK-PD9), use a small object like a screw driver to press into the slots located on the end of the cover. Using Table 1 or Table 2 below, select an AC or DC Power Source that provides enough current to power the number of devices to be used. The Power Source voltage must also match the device's voltage requirements. Mount the Power Distribution Module near the Power Source that will be used to power the devices. Connect the Power Source to the Power Distribution Module via the two Input Power Screw Terminals or the 2. 1mm DC jack(J1) located to the right of the terminals. Connect a two conductor cable from the Power Distribution Module's Output terminals to the devices to be powered. If desired, the total current draw can be measured at the Master Power Switch using an Ammeter while the switch is off. Turn the Master Power Switch on, ensure all leds are on. Replace the plastic cover on the Power Distribution Module. Table 1: Sizing the Power Supply Table 2: Quick Power Supply Selection by Number of Devices Calculate the total combined power consumption of Select a column that closely approximates the power consumption of each device. Select a Power Supply which has a desired voltage, select the row that meets or exceeds the number of desired devices. [. . . ] Available Power Amps VA / W atts 4A 48 @400mA @300mA (4. 8Watts) (3. 6Watts) 10 13 @250mA (3Watts) 16 @200mA @150mA @125mA @100mA (2. 4Watts) (1. 8Watts) (1. 5Watts) (1. 2Watts) 20 26 32 40 Figure 2: Power Distribution Module(ELK-PD9) POWER 1 POWER 2 POWER 3 POWER 4 POWER 5 POWER 6 POWER 7 POWER 8 POWER 9 POS NEG POS NEG POS NEG POS NEG POS NEG POS NEG POS NEG POS NEG POS NEG TOTAL CURRENT DRAW CAN BE MEASURED BY ATTACHING A CURRENT METER TO THESE TEST POINTS LOCATED ON SW1 LEADS SW1 MUST BE TURNED OFF IN ORDER TO MEASURE THE CURRENT ON LED PTC OFF LED PTC LED PTC CONNECT DEVICES TO BE POWERED TO THESE TERMINALS Observe Polarity if using DC Voltage LED PTC J1 CENTER PIN + LED PTC LED PTC LED PTC LED PTC 07/04 + 24VAC or 24VDC or 12VDC LED PTC CONNECT INPUT POWER HERE 12 or 24 VOLTS AC or DC (30 VOLTS MAX)* * WARNING!THE SIZE OF THE INPUT POWER SOURCE MUST BE LARGER THAN THE COMBINED TOTAL LOAD OF THE ATTACHED DEVICES. THE INPUT POWER SOURCE MUST ALSO MATCH THE DEVICE'S OPERATING VOLTAGE SPECIFICATIONS OPTIONAL: 12 VOLT DC PLUG-IN POWER SUPPLY NEG POS SW1 POWER DISTRIBUTION 9 OUTPUTS [. . . ]