User manual EMERSON FANS ATHENIAN

[. . . ] READ AND SAVE THESE INSTRUCTIONS ® ATHENIANTM Ceiling Fan Owner's Manual Net Weight: Model No. 21. 6 Lbs. CF2400AB00 CF2400BC00 CF2400ORB00 CF2400PW00 CF2400SCK00 CF2400WB00 LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for a lifetime of your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. [. . . ] Use three 10-32 x 3/8" Phillips pan head screws (supplied) and three #10 flat washers to secure the fan blade to the blade flange (Figure 5). Repeat this procedure for the remaining four blades. 10-32 x 3/8" PHILLIPS PAN HEAD SCREWS (3) #10 FLAT WASHERS (3) Figure 3 FAN BLADE NOTE: Lightly snug the knurled knobs and make sure the wires and wire connectors are completely inside the motor coupling cover and not pinched between the motor coupling cover and the motor. Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top (Figure 4). BLADE FLANGE 5 Figure 5 11. Use the 10 round recessed holes in the motor hub that are marked with a "5" and install the five blade assemblies in accordance with Step 12. One side of the switch housing has been indented to allow easy access when installing the flange screws. ! ! WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. outlet box listed as "Acceptable for Fan Support". WARNING To reduce the risk of personal injury, do not bend the blade flanges when installing the flanges, balancing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades. 1. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box. Attach one blade assembly to the motor hub using two 10-32 x 5/8" oval head screws (supplied) (Figure 6). Install four remaining blade assemblies in the same way. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence. Next, securely tighten all flange screws, again working in a clockwise sequence. Failure to follow this procedure could result in fan wobble. This completes the blade installation. Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. OUTLET BOX TWO SCREWS SUPPLIED WITH OUTLET BOX TAB Figure 8 HANGER BRACKET BLADE FLANGE 2. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 9). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 8). ! WARNING 5 MOTOR SWITCH HOUSING HUB Figure 6 The fan must be hung with at least 7' of clearance from floor to blades (Figure 7). CEILING Figure 9 5 4 10-32 x 5/8" OVAL HEAD SCREWS (2 per blade assmebly) Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. How to Hang Your Ceiling Fan ! NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY. OUTLET BOX WARNING HANGER BRACKET HANGER BALL/ DOWNROD ASSEMBLY THREADED STUD (2) !AT LEAST 7' WARNING To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket. Figure 7 FLOOR 6 How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. ! EMERSON FAN CONTROL LISTED OUTLET BOX GREEN WIRE (GROUND) FROM HANGER BRACKET GROUND WIRE BLACK BLACK FAN WIRE RED LIGHT CONTROL BLACK (HOT) TO 120 VOLT SUPPLY WARNING WHITE WHT. BLUE GREEN WIRE (GROUND) FROM HANGER BALL LISTED WIRE CONNECTOR (4) GROUND Turning off wall switch is not sufficient. [. . . ] Wire connectors inside switch housing rattling. WARNING: Make sure main power is turned off. 1. Check to make sure the screws which attach the blade flanges to the motor are tight. Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing. ! WARNING: Make sure main power is turned off. 4. Screws holding blades to flanges are loose. [. . . ]