User manual EMERSON FANS BANFF

[. . . ] BP7309 BANFF 1/5/06 9:59 AM Page 1 READ AND SAVE THESE INSTRUCTIONS Model No. BANFFTM 52" Ceiling Fan Owner's Manual CF720ORB00 CF720PW00 CF720WB00 Net Weight: 22. 2 Lbs. INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] If bracket and/or outlet box are not securely attached, the fan could wobble or fall. To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket. How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. ! OUTLET BOX TWO SCREWS SUPPLIED WITH OUTLET BOX TAB WARNING HANGER BRACKET Figure 8 2. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 9). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 8). Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. CAUTION: To reduce the risk of electrical shock, disconnect the electrical supply circuit before installing the fan, light kit or receiver. ! WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. 8 BP7309 BANFF 1/5/06 9:59 AM Page 9 1. Position the supply wires to the left side of the outlet box (Figure 10); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 10. NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Refer to Figures 10 and 11 and connect the receiver wires to the supply wires and the fan motor wires as follows: a. Securely connect the green grounding wires from the hanger ball and the hanger bracket to the supply grounding conductor (this may be a bare wire or a wire with green insulation). Securely connect the supply white (neutral) wire to the receiver white (AC IN N) wire. SUPPLY WHITE WIRE (NEUTRAL) c. Securely connect the supply black wire (hot) wire to the receiver black (AC IN L) wire. Securely connect the fan motor white wire to the receiver white (TO MOTOR N) wire. Securely connect the fan motor black wire to the receiver red (TO MOTOR L) wire. Securely connect the fan motor blue wire to the receiver blue (FOR LIGHT) wire. ! WARNING Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. RECEIVER WHITE WIRE RECEIVER BLACK WIRE AC IN SUPPLY BLACK WIRE (HOT) GROUND WIRE N RECEIVER RED WIRE RECEIVER BLUE WIRE TO MO ANTENNA GREEN GROUND WIRE FROM HANGER BRACKET 1-1/4" THREADED STUD (2) FAN BLACK WIRE FAN BLUE WIRE FAN WHITE WIRE RECEIVER WHITE WIRE Figure 10 9 FOR LI GREEN GROUND WIRE FROM HANGER BALL TOR N AC IN L GHT TO M OTO RL BP7309 BANFF 1/5/06 9:59 AM Page 10 SW101 FAN/LIGHT WALL CONTROL (SUPPLIED) TO 120VOLT SUPPLY BLACK (HOT) OFF BLACK HI LIGHT MED BLACK WHITE WHITE RED LOW FAN OFF EMERSON® ON WHITE GROUND TWO-CONDUCTOR CABLE (WITH GROUND) GREEN WIRE (GROUND) FROM HANGER BALL AND HANGER BRACKET BLUE BLACK BLUE WHITE WHITE Figure 11 3. Push the wires and connectors up into the outlet box while inserting the receiver fully into the hanger bracket. [. . . ] Do To Correct Problems: Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OR REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO. [. . . ]