User manual EMERSON FANS BOTANICA

[. . . ] READ AND SAVE THESE INSTRUCTIONS "Botanica" Series Model No. CF2500OB01 CF2500S01 Net Weight: CF2500HTW01 CF2500TG01 20. 0 Lbs. ® Botanica Series Ceiling Fan Owner's Manual Part No. BP7220-3 ! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner's manual carefully and keep it for future reference. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. [. . . ] Retain the pin and hanger ball for reinstallation in step 9. CLEVIS PIN HANGER BALL DOWNROD DOWNROD HAIRPIN CLIP CLEVIS PIN CLEVIS PIN MOTOR COUPLING Figure 16 SETSCREW 4. Push the uplight yellow lead assembly connector through the downrod (Figure 17) until it extends about 4". Cut the yellow lead approximately 3" from the end of the pipe. Strip insulation 1/2" from end of the wires. Using the wire connector supplied, connect the uplight yellow lead assembly to the yellow lead from the fan motor and housing assembly (Figure 18). 4" UPLIGHT YELLOW LEAD ASSEMBLY CUT HERE Figure 18 9. Install the setscrew (supplied in loose parts bag) in the motor coupling and tighten using the 5/32" setscrew wrench (supplied) (Figure 19). DOWNROD 3" Figure 17 8 ! DOWNROD WARNING It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. SETSCREW PIN MOTOR HANGER BALL DOWNROD SETSCREW Figure 19 10. Screw two 1" threaded studs (provided) into the motor (Figure 20). Leave approximately 7/8" of the stud extending above the motor. Slide the motor cover over the downrod and rotate the cover until the threaded studs protrude; install two knurled knobs (supplied) to secure the cover. NOTE: Make sure the red and brown leads are separately capped with wire connectors. Make sure red, brown, and yellow wire connectors are completely inside motor coupling cover and not pinched between the motor coupling cover and motor. CEILING COVER Figure 21 14. Use three 10-24 x 3/8" pan head screws and flat washers (supplied) to secure flange to blade (blades ordered separately) (Figure 22). Repeat for the remaining four blades. 10-24 x 3/8" PAN HEAD SCREW (3) FLAT WASHER (3) KNURLED KNOB BLADE WIRE CONNECTORS RED LEAD BROWN LEAD MOTOR COUPLING COVER WIRE CONNECTOR YELLOW LEAD 1" THREADED STUD 7/8" BLADE FLANGE MOTOR Figure 22 15. Using the 5/32" hex wrench (supplied), loosen the setscrew in the collar and unscrew (counterclockwise) the switch housing assembly from the motor shaft (Figure 23). Do NOT remove the flat washer from the motor shaft. BLADE FLANGE Figure 20 11. Position the ceiling cover over the downrod. Be sure the cover is oriented correctly, with the large opening at the top (Figure 21). Reinstall the hanger ball on the downrod as follows. Route the motor leads through the hanger ball and slide the hanger ball over the downrod (Figure 21). Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod, aligning the ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. [. . . ] All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR. What Will Emerson Company Do To Correct Problems: Emerson will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will refund the actual purchase price of your fan. [. . . ]