User manual EMERSON FANS DESIGNER

[. . . ] READ AND SAVE THESE INSTRUCTIONS Model No. by ® DESIGNER Ceiling Fan Owner's Manual CF755AB04 CF755OB04 CF755BK04 CF755WW04 CF755S04 CF755DB04 CF755W04 CF755BS04 CF755BQ04 CF755AW04 CF755NW04 CF755PB04 CF755TG04 CF755H04 CF755WPB04 CF755V04 CF755HTW04 CF755WB04 CF755PW04 Net Weight: 17. 3 Lbs. LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for thirty years from the date you purchased your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. [. . . ] Remove the upper setscrew from the motor coupling. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 2). The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the downrod to make sure the clevis pin is properly installed. Reinstall the upper setscrew in the motor coupling. Check that the lower setscrew is tightened securely (Figure 2). NOTE: The setscrews must be properly installed as described above, or fan wobble could result. ! Figure 3 4. Reinstall the hanger ball (Figure 4) on the downrod as follows. Route the three 80" motor leads through the hanger ball. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. ! WARNING It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. PIN HANGER BALL WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tightened. Failure to verify that the pin and setscrews are properly installed could result in the fan falling. DOWNROD SETSCREW MOTOR COUPLING SETSCREW CLEVIS PIN Figure 4 HAIRPIN CLIP DOWNROD CLEVIS PIN UPPER SETSCREW CLEVIS PIN HAIRPIN CLIP SETSCREW MOTOR COUPLING Figure 2 5. The fan comes with blue, black and white leads that are 80" long. Before installing fan, measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. FAN BLADE BLADE FLANGE ! WARNING Figure 7 NOTE: Take care not to scratch fan housing when installing blades. NOTE: Remove and discard the four shipping spacers and screws from the motor hub. Loosely attach one blade assembly to the motor hub using two 1/4-20 x 1/2" Phillips oval head flange screws. [. . . ] Make sure reversing switch position is all the way to one side. Check to make sure all screws in motor housing are snug (not over-tight). Check to make sure the screws which attach the fan flanges to the motor hub are tight. Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing. [. . . ]