User manual EMERSON FANS LARISSA

[. . . ] BP7307 Larissa KF220 1/9/06 8:36 AM Page 1 READ AND SAVE THESE INSTRUCTIONS Emerson Fans Designed by LARISSA Ceiling Fan Owner's Manual Model Numbers KF220TZG00 Tannery Bronze Housing with Gold Accents and Dark Cherry/Walnut Blades ¨ KF220GLZ00 Gilded Silver with Natural Cherry/ Mahogany Blades KF220AGW00 Aged Walnut with Teak/Mahogany Blades Net Weight: 33. 7 Lbs. Part No. BP7307 BP7307 Larissa KF220 1/9/06 8:36 AM Page 2 ! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner's manual carefully and keep it for future reference. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. [. . . ] Refer to Figures 14 and 15 and connect the receiver wires to the supply wires and the fan motor wires as follows: a. Securely connect the green grounding wires from the hanger ball and the hanger bracket to the supply grounding conductor (this may be a bare wire or a wire with green insulation). Securely connect the supply white (neutral) wire to the receiver white (AC IN N) wire. Securely connect the supply black wire (hot) wire to the receiver black (AC IN L) wire. Securely connect the fan motor white wire to the receiver white (TO MOTOR N) wire. Securely connect the fan motor black wire to the receiver red (TO MOTOR L) wire. Securely connect the fan motor blue wire to the receiver blue (FOR LIGHT) wire. ! WARNING Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. RECEIVER WHITE WIRE RECEIVER BLACK WIRE AC IN SUPPLY BLACK WIRE (HOT) GROUND WIRE N RECEIVER RED WIRE RECEIVER BLUE WIRE TO MO ANTENNA GREEN GROUND WIRE FROM HANGER BRACKET 1-1/4" THREADED STUD (2) FAN BLACK WIRE FAN BLUE WIRE FAN WHITE WIRE RECEIVER WHITE WIRE Figure 14 11 FOR LI GREEN GROUND WIRE FROM HANGER BALL TOR N AC IN L GHT TO M OTO RL BP7307 Larissa KF220 1/9/06 8:36 AM Page 12 SW101 FAN/LIGHT WALL CONTROL (SUPPLIED) TO 120VOLT SUPPLY BLACK (HOT) OFF BLACK HI LIGHT MED BLACK WHITE WHITE RED LOW FAN OFF EMERSON® ON WHITE GROUND TWO-CONDUCTOR CABLE (WITH GROUND) GREEN WIRE (GROUND) FROM HANGER BALL AND HANGER BRACKET BLUE BLACK BLUE WHITE WHITE Figure 15 3. Push the wires and connectors up into the outlet box while inserting the receiver fully into the hanger bracket. Position the antenna wire on top of the receiver. Screw the two 1-1/4" threaded studs (supplied) into the tapped holes in the hanger bracket (Figure 14). Lift the ceiling cover up to the threaded studs and turn until the studs protrude through the holes in the ceiling cover (Figure 16). Secure the ceiling cover in place by sliding lockwashers (supplied) over the threaded studs and installing the two knurled knobs (supplied). Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling. ! HANGER BALL WARNING To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. Screw in three 40-watt (maximum) candelabra bulbs in the light fitter sockets (Figure 17). Carefully place the lower glass over the light fitter threaded nipple. Be sure the glass is firmly seated in the decorative ring, then secure in place using a rubber washer, metal washer, and nut (washers and nut are supplied). Place the decorative cap over the threaded nipple and then screw on the finial nut (Figure 17). Your ceiling fan is now installed and wired to be controlled by your fan/light wall control. CEILING COVER 1-1/4" THREADED STUD LOCKWASHER (2) KNURLED KNOB (2) Figure 16 12 BP7307 Larissa KF220 1/9/06 8:36 AM Page 13 ANTENNA WIRE DECORATIVE RING ON 40-WATT (max. ) CANDELABRA BULBS (3) SOCKET LIGHT FITTER THREADED NIPPLE 1 2 3 4 RECEIVER CODE SWITCH WALL CONTROL LEVERS 1 ON RECEIVER SWITCH LEVERS 1 ON 2 3 4 CODE SWITCH RUBBER WASHER LOWER GLASS METAL WASHER NUT DECORATIVE CAP FINIAL NUT WALL CONTROL Figure 18 Figure 17 Installation of Wall Control SINGLE-POLE INSTALLATION (Figure 19) HOT BLK HI LIGHT MED LOW FAN OFF Setting Operating Frequency of Wall Control and Receiver (Figure 18) Your wall control and receiver have code switches which must be set in one of 16 possible code combinations. [. . . ] will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson Electric Co. will refund the actual purchase price of your fan. We will ship the repaired product or replacement to you at no charge, but you are responsible for all costs or removal, reinstallation and shipping of the product to Emerson Electric Co. [. . . ]