User manual EMERSON FANS MONTEREY

[. . . ] READ AND SAVE THESE INSTRUCTIONS Model No. ® MONTEREY Ceiling Fan Owner's Manual LIMITED WARRANTY CF770AW01 CF770BC01 CF770BS01 CF770OB01 CF770ORB01 CF770TG01 CF770WW01 Net Weight: 19. 8 Lbs. What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for thirty years from the date you purchased your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. [. . . ] Separate, untwist and unkink the three 80" motor leads. Route the motor lead wires through the downrod. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 2). The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the downrod to make sure the clevis pin is properly installed. ! Figure 3 WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed (as shown in Figure 2) could result in the fan falling. 5. Reinstall the hanger ball (Figure 4) on the downrod as follows. Route the three 80" motor leads through the hanger ball. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of the hanger ball. Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball. A loose setscrew could create fan wobble. ! WARNING MOTOR COUPLING 3/16-24 x 1/2" SETSCREW CLEVIS PIN HAIRPIN CLIP It is critical that the pin in the hanger ball is properly installed and the setscrew securely tightened. Failure to verify that the pin and setscrew are properly installed could result in the fan falling. PIN JAM NUT DOWNROD HAIRPIN CLIP 3/16-24 x 1/2" SETSCREW DOWNROD HANGER BALL MOTOR COUPLING CLEVIS PIN SETSCREW Figure 2 JAM NUT 3. Back off the jam nut until it rests loosely against the setscrew head. Install the setscrew in the motor coupling (Figure 2) and tighten securely while pulling up on the downrod. Using a 5/16-inch open end wrench or pliers, tighten the jam nut securely against the motor coupling. You have now completed the assembly of your new ceiling fan. You can now proceed with hanging and wiring your fan. SWITCH HOUSING ASSEMBLY SWITCH HOUSING PLATE MOUNTING SCREWS (3) Figure 8 BLADE FLANGE Figure 6 MOTOR HUB Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. ! The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. ! WARNING To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked "Acceptable for Fan Support", and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. [. . . ] Check to make sure the screws which attach the fan flanges to the motor are tight. Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing. WARNING: Make sure main power is turned off. Some fan motors are sensitive to signals from Solid-State variable speed controls. [. . . ]