User manual EMERSON FANS PREMIUM

[. . . ] READ AND SAVE THESE INSTRUCTIONS Model No. ® PREMIUM Series CF4800WW03 CF4800BQ03 CF4800AW03 CF4800WB03 CF4800PW03 CF4800TG03 CF4800OB03 CF4800CK03 CF4800BS03 CF4800AB03 CF4800PB03 CF4800S03 CF4800NW03 CF4800HTW03 CF4800WPB03 CF4800BC03 CROWN Series CF4500AB04 CF4500OB04 CF4500PB04 CF4500HTW04 CF4500BC04 PREMIUM & CROWN Series Ceiling Fan Owner's Manual Net Weight: 20. 0 Lbs. LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for the lifetime of your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. [. . . ] Consult a qualified electrician if in doubt. Connect the black wire from the wiring harness to the black (hot) supply wire (Figure 4A). Connect the white wire from the wiring harness to the white (neutral) supply wiring. Connect the green ground wires from the hanger bracket and the hanger ball to the supply ground wire. Use wire connectors supplied with your ceiling fan. ! Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. OUTLET BOX WARNING Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. TWO SCREWS SUPPLIED WITH OUTLET BOX TAB HANGER BRACKET 20. Securely connect the wiring harness connector to the receiver connector, and connect the blue and yellow wires to the blue and yellow wires from the receiver (Figure 4A). Figure 11A 7 21. Turn the receiver so that the flat side aligns with the open side of the hanger bracket (Figure 13A). Fold and position the wires into the space above the hanger ball and into the outlet box. Feed the wires and connectors around the outside of the receiver, through the open side of the hanger bracket, and into the outlet box. Slide the receiver up and over the hanger bracket. Remove the backing on the foam adhesive pads and press the receiver against the ceiling. SECTION B Assembly Instructions for Installing the CF4800 or CF4500 Ceiling Fan to Control the Built-in Uplight with the Pull Chain in the Switch Cup 1. Position the fan motor and housing assembly in the lower foam packing so that the top of the motor is facing you. Separate, untwist and unkink the four motor leads. Obtain the hanger ball/downrod assembly and remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1B). Remove the pin from the downrod , then remove the hanger ball. Retain the pin and hanger ball for reinstallation in Step 6. CLEVIS PIN HANGER BRACKET HANGER BALL RECEIVER OPEN SIDE FLAT SIDE HANGER BALL Figure 1B DOWNROD SETSCREW Figure 13A CEILING COVER 23. Screw the two 1-1/4" threaded studs (provided) into the tapped holes in the hanger bracket. Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover (Figure 14A). [. . . ] Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing. Raise motor cover and tighten setscrew securely. Tighten the setscrew in the hanger ball/ downrod assembly. Check to be sure screws which attach the fan blade flanges to the motor hub are tight. [. . . ]