User manual EMERSON FANS RAPHAEL

[. . . ] READ AND SAVE THESE INSTRUCTIONS Raphael Model No. CF2600AB01 CF2600WB01 CF2600PW01 Raphael II Model No. Net Weight: 29. 5 Lbs. CF2650BC01 CF2650WB01 CF2650PW01 ® RAPHAELTM / RAPHAEL IITM Ceiling Fan Owner's Manual LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for a lifetime from the date you purchased your ceiling fan. All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. [. . . ] Attach one blade assembly to the motor hub using two 10-32 x 5/8" oval head screws (supplied) (Figure 17A). Install remaining blade assemblies in the same way. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence. Next, securely tighten all flange screws, again working in a clockwise sequence. Failure to follow this procedure could result in fan wobble. Pass the connectors and the wires form the motor shaft through the washer (supplied) and position the washer over the motor shaft (Figure 17A). MOTOR HUB CEILING COVER 1-1/4" THREADED STUD KNURLED KNOB LOCKWASHERS (2) BLADE FLANGE WASHER 10 - 32 x 5/8" OVAL HEAD SCREW (2 Per Blade Assembly) MOTOR SHAFT Figure 15A Figure 17A ! WARNING To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling. 8 31. Using the 5/64" hex wrench (supplied), loosen the setscrew in the collar on the light kit adapter assembly. Then pass the connectors and the wires from the motor shaft through the collar (Figure 18A). Screw the adapter assembly onto the motor shaft and then tighten the setscrew to secure the adapter assembly to the motor shaft. Connect the connectors from the motor shaft using the jumper assembly (supplied). Verify that the connectors are securely engaged. 34. Install two candelabra base lamps in the sockets of the light kit adapter plate (Figure 20A): Model CF2600 - 15-Watt Maximum Model CF2650 - 25-Watt Maximum 35. Position the glass shade over the threaded nipple in the light kit plate assembly (Figure 20A). Seat the glass shade evenly over the plate assembly and securely install the hex nut and finial nut (supplied) on the threaded nipple. 5/32-32 x 3/16" PHILLIPS HEAD SCREW (3) COLLAR SETSCREW LIGHT KIT PLATE ASSEMBLY LIGHT KIT ADAPTER ASSEMBLY SOCKET THREADED NIPPLE Figure 18A JUMPER ASSEMBLY 32. Securely connect the black wire from the light kit plate assembly to the blue wire from the motor shaft using a wire connector (supplied) (Figure 19A). Connect the white wire from the plate assembly to the white wire form the motor shaft using a wire connector (supplied). GLASS SHADE, LOWER HEX NUT 1/8-27 FINIAL NUT WIRE CONNECTORS WHITE WIRES Figure 20A LIGHT KIT PLATE ASSEMBLY BLUE WIRE BLACK WIRE Figure 19A NOTE: When installing the light kit plate assembly, position the wires and wire connectors in the raised center portion of the plate assembly. Do not pinch wires between the light kit plate assembly and the adapter assembly. Secure the light kit plate assembly to the light kit adapter assembly by threading three 5/32-32 x 3/16" phillips head screws (supplied) into the threaded holes in the adapter assembly (Figure 20A). 9 SECTION B Assembly Instructions for Installing the CF2600 and CF2650 Ceiling Fan Controlled by Emerson Fan/Light Controls (other than SR330 or SW350) or Standard Wall Switches 1. Position the motor housing and shade assembly in the foam packing so that the top for the motor is facing you. Obtain the hanger ball/downrod assembly and remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1B). Remove the pin from the downrod, then remove the hanger ball. [. . . ] Tighten the barrels of the rod assemblies. Check to make sure the screws which attach the fan flanges to the motor hub are tight. WARNING: Make sure main power is turned off. Check to make sure wire connectors in switch housing are not rattling against each other or against the interior wall of the switch housing. [. . . ]