User manual EMTEC USB-MODUL FR WIFI WI300

[. . . ] Press ENTER to go to next step, press RETURN to cancel, and press PLAY to connect. 4 / 14 · Get Connection Mode Choose between Infrastructure (AP) and Peer to Peer (Ad Hoc). Press ENTER to go to next step, and press RETURN to cancel. 2. 1 Infrastructure (AP) Infrastructure mode is used to connect computers with wireless network adapters, also known as wireless clients, to an existing wired network with the help from wireless router or access point. · Get SSID Name Press ENTER to go to next step, press RETURN to cancel, and press SELECT to refresh the SSID list. Note: In the Security list, WEP (Wired Equivalent Privacy) and WPA (Wi-Fi Protected Access) means the network is encrypted, i. e. [. . . ] The computerto-computer network will be built. And the network status will be changed into Connected. 9 / 14 Note: If the SSID you wish to connect is not in the list, please click Refresh network list, and try again. · Setup the IP address for PC Step1: Select Change advanced settings in Wirleless Network Connection dialog box. 10 / 14 Step 2: Click Properties. Step 3: Double click Internet Protocol (TCP/IP). Click Use the following IP address, and manually enter the IP address, Subnet mask, and Default gateway. Note: Be sure to put the player and the PC on the same subnet and in the same IP range. For example, if you set the IP on the player to 192. 168. 1. 3, be sure to set the PC to something different inside that same range (192. 168. 1. 2-254). 11 / 14 · Set the network adapter/card to run in `ad hoc' mode Step 1: Click Wireless Networks tab on Wireless Network Connection Properties dialog box. Note: You can also click Add to manually add the wireless SSID here. Step 2: Select your SSID in Preferred networks, and click Properties. Step 3: Select Network Authentication and Data encryption mode properly, and make sure a check has been added to the box to specify that This is a computer-to-computer (ad hoc) network; wireless access points are not used. Click OK to save the entry. 12 / 14 3. Getting Started When the wireless setup is done, you can start using the powerful wireless function of this player, and enjoy the happiness. 3. 1 Browsing Content via WLAN You can view the multimedia files shared on the wireless network in the Browser menu. When selecting NET in the Browser menu, there are two ways to locate the multimedia files shared on your WLAN. One way is to browse through workgroup; the other way is to browse through My Shortcuts. Operations are the same as the wired network function. Please refer to the chapter about Network Function in the user manual; 2. While browsing high definition video files (resolution up to 720p / 1080i / 1080p) via WLAN, the video might be buffering. It is normal due to the limit of network speed and signal strength. 3. 2 Network Copy Press the F1 button on the remote control, there appears the File Copy menu where you are allowed to copy files between USB, HDD, and NET. Operations are specified in the chapter about File Copy in the user manual. 3. 3 NAS function This player can be used as a NAS (Network-Attached Storage) device. When the network connection is done correctly and ready for use, type: \\NAS or \\IP Address in the Run window (click Run in the start menu) or the address bar of Internet Explorer on your PC (For example, if the IP address of the player is 192. 168. 0. 9, please type: \\192. 168. 0. 9 or \\NAS), and click OK or press the Enter button on the keyboard. Then you can view, and edit the files stored on the hard disk installed on the player. In this way, you can playback and copy files via wireless network between your PC and the player without a USB or Ethernet cable. 13 / 14 Note: NTFS partitions will be read-only. 4. [. . . ] Then, type in the Run field: `secpol. msc', and click OK. It will bring you to Vista's security policy system. Once there, go to: `Local Policies' -> `Security Options', and then find: `Network Security: LAN Manager authentication level'. Change the Setting from `Send NTLMv2 response only' to `Send LM & NTLM -- use NTLMv2 session security if negotiated'. [. . . ]