User manual ENEO VKC-1330IR

[. . . ] Montage und Betriebsanleitung Farb-Kamera VKC-1330IR12-24, VKC-1330/IR Installation and Operating Manual Colour Camera VKC-1330IR12-24, VKC-1330/IR Mode d'emploi Caméra Couleur VKC-1330IR12-24, VKC-1330/IR 1 Inhaltsverzeichnis 1. Sicherheitshinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Allgemeine Beschreibung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Anschluss und Bedienung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To adjust the backfocus open screw M, turn at CS mount ring L until the focus maximum is achieved and fasten the screw again. Connector for control interface and day/night switch 18 C D Power supply LEVEL E F LENS UP, Menu, DOWN G VIDEO HO, Camera mount HU K, L C/CS mount M N Fixing screw 6 PIN Adjustment for control interface connector N PIN SI GND RX TX 485485+ Description D/N switch GND RS-232 RXD IN RS-232 TXD OUT RS-485 RS-485 + SI GND Colour B/W Contact Open Closed 3. 1 Sample Connections for the Use of Multiple Cameras Switchover unit Video OUT jack 12VDC 230V / 50Hz Video OUT jack Video IN jack Video IN jack Video OUT jack Video IN jack 12VDC 230V / 50Hz Monitor Note Read the installation and operating manual first. Power up unit and other components only after all connections are made. 19 4. Pinout Power Supply at the VKC-1330IR12-24 12VDC 24VAC G G Note Only switch on the power supply when all the other connections have been carried out. The use of power supply units with stabilised output voltage (12VDC ±10%) is recommended. 3 1 4 2 Connector assignment for DC voltage controlled lenses Description 1 2 3 4 Damping (-) Damping (+) Control (+) Control (-) Lens connection AE status of menu should be selected to manual mode and shutter speed is fixed at normal status. A/I switch in dc position To be optimized with LEVEL potentiometer Use only DC voltage controlled lenses with internationally standardized plug pinout. Signal level Remark 3 1 4 2 Connector assignment for Videosignal controlled lenses Description 1 2 3 4 Supply voltage N. C. Video Ground Colour red ­ white black Lens connection AE status of menu should be selected to manual mode and shutter speed is fixed at normal status. A/I switch in video position Optimise via the , , LEVEL" regulator on the AI lens. 20 Signal level 5. Lens Mounting and Adjustment Lens Mounting N Dust protection cap Lens C/CS mount Remove dust cover N before screwing on the lens. Screw in the lens, and with lenses with automatic iris control, plug the lens cable into the , , LENS" socket. When using a C mount lens, screw on the C mount ring K. Adjustment ­D LEVEL Note Video level adjustment Deactivation of the functions shutter and AGC is recommended for video level adjustment. Attention should be paid to sufficient illumination. Once the camera is supplied with voltage and connected to a monitor, undertake sensitivity control on the camera via potentiometer D (when using DC controlled lenses adjust at the camera, when using auto iris lenses adjust at the lens). Appropriately this takes place by means of an oscillograph and a sufficiently illuminated test pattern (min. Should these auxiliary means be unavailable, one must attempt to make an approximate adjustment according to the subjective impression made by the picture, whereby the potentiometer must be turned to the left in the event of an dense picture or to the right in the event of little contrast. (Increase in brightness on the monitor ­> rotational direction of the LEVEL-potentiometer clockwise. Reduction in brightness on the monitor ­> rotational direction of the LEVEL-potentiometer anticlockwise). Mean value/peak value control (auto iris lenses only): If the impression made by the picture is unsatisfactory in spite of correctly adjusted level, this may result from strong differences in brightness in the picture (possibly highlight areas), which falsify the adjustment. Remedial action takes place via the potentiometer ALC (at the lens). Continuous adjustment up to 100% peak value control, thus improved recognisability of dense picture sections, is possible by turning the potentiometer to the left. 21 6. Adjustment of Lenses M K M C mount lens CS mount lens L AL L Adjustment of flange focus for fixed focus lenses This adjustment (distance between lens casing and sensor surface) is required if a sharp definition cannot be obtained with the lens focussing, or in order to adjust the position. To obtain a sharp definition, point the camera at an object which is at least 2000 times further away from the front of the lens than the focal length. [. . . ] DNR est désactivé en mode arrêt sur image, obturateur à faible vitesse et WDR. WDR est désactivé en cas d'arrêt sur image. OFF OFF OFF OFF OFF OFF INT Preset Default Preset OFF 8. Dépannage En cas de problème, vérifiez l'installation de la camera selon les instructions du present manuel et par rapport aux autres équipements. Localisez le problème qui affecte un équipement donné dans le système et reportez-vous au manuel de cet équipement pour plus d'informations. Problème Pas d'image Solution possible 1. [. . . ]