User manual ENGENIUS SN-920

[. . . ] S N - 9 2 0 U LTRA EnGenius Technologies Customer Service USA:888-735-7888 Canada:888-397-2788 Literature order number:120-0002-04 User's Manual Table of Contents Congratulations Handset Diagram Features 3 4 1 Voice Volume Call On-Hold Muting a Call Call Waiting Transferring a Calls Disconnecting Calls 25 26 27 28 28-31 31 Advanced Operations 2-Way Radio Handset-to-Handset Base-to-Handset Handset-to-Base Base Unit Options Ring Volume Voice Volume Main Menu Function Chart Handset /Base Registration Registering a Handset De-registering Handset Registering additional Base Units Handset Menu Options Key Guard Directory Caller ID Sounds Ring Volume Ring T ype Key Volume Key T one Settings Area Code T one/ Pulse Backlight Reset 32 33 34 35 35 36 37-39 39 40-41 42 42-50 50-53 53-54 54 54 54 55 56 56 57 Base Unit Diagram Features 8 9 Charging Cradle Diagram Features 10 11 Getting Started Base Unit Set-up Charging Cradle Set-up 12-13 13-15 Basic Operations Modes Making Calls Manual Dail Pre-dial tone Manual Dail Post-dial tone Redial Directory Dial Memory Dial Answering Calls Handset in Charging Cradle Handset not in Charging Cradle Silent Feature 16-19 20 21 21 21-22 22-23 25 25 25 Custom Name Call Manager Contrast Dial Prefix 57 58-59 59 60 61 62-66 67-68 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1)this device may not cause harmful interference, and 2)this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this phone. Product Specifications Safety Instruction Regulatory Information CAUTION: When selecting a location for the base unit, it is better to locate the base unit as high as possible to avoid obstructions that might interfere with the radio transmission and getting a clear signal. In any case, the base unit must be located 8 inches (20cm) from any person to be in compliance of FCC safety regulations. Person with pacemaker: Should always keep the handset more than 8 inches (20 cm) from their pacemaker when the handset is on and should not carry the handset in a breast pocket. [. . . ] Press the "6" key to select the REGISTER option. Press the "4" key to select RESET HAND. The LCD will display the following screen: YES NOTE: If there is more than one base unit and a handset is to be registered to more than one base unit, the base unit's identification number must be changed from factory default number of "1" to either "2", "3", or "4". Plug in the new base unit to AC power and place a fully charged battery pack into the handset. Dereg from all bases?Verify base unit's power light is on and turn on the handset power by pressing and holding the END key for 2 seconds. ~ 39~ ~ 40~ 3. Place base unit into REGISTRATION mode by pressing and holding the VOLUME and PAGE buttons at the same time until you hear a single beep (about 3 seconds). The red "In-Use" light will come on. Handset registration must be preformed within 30 seconds after entering the registration Mode. Pressing the RIGHT SOFT BUTTON, on the handset, selects the MENU function. Press the number " 6" button on the handset keypad, this will place the handset into the re g istration menu. Press the number " 3" button on the handset keypad. The handset Display will now request that you "Enter base ID (1-4): *" 8. Enter a number "1", "2", "3", or "4" from the keypad. Choose a base ID number different from base ID number you are already using. Repeat steps 1 through 8 for each new base you want to re g ister. Enter base ID (1-4): * Reg Menu 1. Reset Hand Handset Menu Options Key Guard Press "MENU", "1" to set KEY GUARD. To access the KEY GUARD option from the IDLE mode, press the RIGHT SOFT FUNCTION key to select the MENU option. While in the MAIN MENU press the "1" key to select KEY GUARD: Main Menu: ¡ ¡ õô 1:KEY GUARD 2:DIRECTORY 3:CALLER ID 4:SOUNDS 5:SETTINGS 6:REGISTER 3. Selecting the KEY GUARD option LO C K S the keypad from use. The screen will display the following: Keypad Locked Unlock 4. To unlock the keypad press the LEFT SOFT FUNCTION key. The screen will display the following: 5. [. . . ] Your telephone company may ask you for this information. The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of the REN's of all devices connected to one line should not exceed five (5. 0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone company to determine the maximum REN for your calling area. [. . . ]