User manual ENVISION EN5100E

[. . . ] EN-5100e EN-5100e 15 inch TFT LCD Monitor User's Manual by Envision Peripherals, Inc. www. ENVISIONmonitor. com Before operating your monitor, please read this manual thoroughly. EN-5100e 1 31MY02 For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock. · Save the original shipping carton and packing materials in case you need to ship your monitor. Be sure to repackage your monitor as it was originally packed at the factory. · Periodically clean your monitor with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. It is UL-listed and CSA labeled for 125 volts AC. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 31MY02 EN-5100e Before You Operate the Monitor Installing & Removing the Base EN-5100e General Features: · 38. 1cm(15") TFT Color LCD Monitor · Crisp, Clear Display for Windows · 1024 X 768 @ 75Hz (Maximum & Recommended Resolution) · EPA ENERGY STAR ® · Ergonomic Design · Space Saving, Compact Case Design EN-5100e Package Contents The box that your monitor was shipped in should have included the following items: 1. Windows 95/98/2000/ME INF Driver Disk 5 31MY02 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied EN-5100e 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into your LCD monitor's power input socket. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). EN-5100e 6 31MY02 Before You Operate the Monitor EN-5100e Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using the power input socket on the back of your computer, you must purchase a power cord with CEE-22 terminated connectors (see illustration above). Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into your LCD monitor's power input socket. Plug the other end of the power cord into the power output socket on your PC. EN-5100e 7 31MY02 Before You Operate the Monitor Adjusting the Viewing Angle EN-5100e For optimal viewing, adjust the monitor's angle to your own preference. [. . . ] Follow the Add New Hardware Wizard instructions on the screen. If the wizard asks for the location of the driver file, select drive A and press Next. EN-5100e 11 31MY02 Technical Support (FAQ) Problem Power LED is not ON EN-5100e Possible Solution · Make sure the power button is ON. · Make sure the power cord is properly connected to a grounded power outlet and to the monitor. · Confirm that your computer is Plug & Play compatible. [. . . ]