User manual ENVISION EN5200EI

[. . . ] EN-5200e/ei EN-5200e/ei 15 inch TFT LCD Monitor User's Manual by Envision Peripherals, Inc. www. ENVISIONmonitor. com Before operating your monitor, please read this manual thoroughly. EN-5200e/ei 1 29JUL02 For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Be sure to repackage your monitor as it was originally packed at the factory. · Periodically clean your monitor with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. It is UL-listed and CSA labeled for 125 volts AC. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 29JUL02 EN-5200e/ei Before You Operate the Monitor Installing & Removing the Base EN-5200e/ei General Features: · 38. 1cm(15") TFT Color LCD Monitor · Crisp, Clear Display for Windows · Supports Resolutions up to 1024 X 768 pixels @75Hz, (1024 x 768 @ 60Hz Recommended) · EPA ENERGY STAR® · Ergonomic Design · Space Saving, Compact Case Design EN-5200e/ei Package Contents The box that your monitor was shipped in should have included the following items: 1. Windows 95/98/2000/ME/XP INF Driver Disk 4. Booklet (Containing Warranty & Safety Information) 5 29JUL02 Before You Operate the Monitor EN-5200e/ei Connecting the Wires Using the Power Cord Supplied (EN-5200e) 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into your LCD monitor's Power Adapter. Connect the Power Adapter to your monitor. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). EN-5200e/ei 6 29JUL02 Before You Operate the Monitor EN-5200e/ei Connecting the Wires Using the Power Cord Supplied (EN-5200ei) 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). EN-5200e/ei 7 29JUL02 Before You Operate the Monitor Adjusting the Viewing Angle EN-5200e/ei For optimal viewing, adjust the monitor's angle to your own preference. [. . . ] 12 29JUL02 Operating Instructions Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. [. . . ]