User manual ENVISION EN7100SI

[. . . ] EN-7100s EN-7100s 17 inch TFT LCD Monitor User's Manual by Envision Peripherals, Inc. www. ENVISIONmonitor. com Before operating your monitor, please read this manual thoroughly. AOC LM720 1 v1_090802 For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. It is UL-listed and CSA labeled for 125 volts AC. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 EN-7100s v1_090802 Before You Operate the Monitor Installing & Removing the Base EN-7100s General Features: · 17" (43. 2cm) TFT Color LCD Monitor · Crisp, Clear Display for Windows · Supports Resolutions up to 1280 X 1024 pixels @75Hz, (1280 x 1024 @ 60Hz Recommended) · EPA ENERGY STAR® · Ergonomic Design · Space Saving, Compact Case Design EN-7100s Package Contents The box that your monitor was shipped in should have included the following items: 1. 5 EN-7100s LCD Monitor Power Adapter Power Cord Windows 95/98/2000/ME/XP INF Driver Disk Quick Start Guide Booklet (Containing Warranty & Safety Information) v1_090802 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied EN-7100s 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into the power adaptor. Connect the power adapter into the DC IN socket on the back of the monitor. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). EN-7100s 6 v1_090802 Before You Operate the Monitor EN-7100s Preparing to Install An Optional Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting arm you purchase separately. Pull the screw covers off the back of the monitor. Remove the base. See next page for further installation instructions. EN-7100s 7 v1_090802 Before You Operate the Monitor Install An Optional Wall Mounting Arm (Not supplied) EN-7100s Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. Insert the 4 screws into the holes and tighten. Insert the power cable into the slot on the back of the monitor. The Envisionl EN-7100s is compatible with the Ergotron line of mounting and arm solutions. Contact Ergotron at 800-888-8458 or visit their web site at www. ergotron. com for more information on the many ways on which you can mount your Envision LCD monitor. EN-7100s 8 v1_090802 Before You Operate the Monitor Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to your own preference. · Hold the stand firmly when you change the monitor's angle. [. . . ] · In order to provide the highest performing products, EPI has set the following limits as to the maximum allowable number of bad pixels: 4 Bright Sub-pixels or 4 Dark Sub-pixels or combination of 6 Dark & Bright. The panel used on this product has a total of 3, 932, 160 sub-pixels. So even the maximum allowed of 6 bad sub-pixels would only amount to a very small 0. 00015% of the total sub-pixels 13 v1_090802 No Plug & Play Picture is fuzzy Picture bounces or a wave pattern is present in the picture Power LED is ON (green or orange light is ON) but there is no video or picture. Missing one of the primary colors (RED, GREEN, or BLUE) Dead Pixel Criteria EN-7100s Technical Support (FAQ) Problem Screen image is not centered or sized properly Picture has color defects (white does not look white) Poor brightness or contrast Horizontal or vertical disturbances on the screen 1CLOCK EN-7100s Possible Solution · Adjust the CLOCK1 and FOCUS2 settings or press the AUTO button to automatically re-configure the monitor's settings. [. . . ]