User manual ENVISION EN9110

[. . . ] EN9110 EN9110 19" LCD Monitor User's Manual By Envision Peripherals, Inc. www. envisionmonitor. com EN9110 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm!Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm!) shall be used. 5 EN9110 INSTALLATIONS INSTRUCTIONS (cont) PREPARING TO INSTALL THE CABLES 1. 2. Remove the wall mounting hole cover. Remove the cable cover. 6 EN9110 INSTALLATIONS INSTRUCTIONS (cont) CABLE CONNECTIONS 1 ­ Connect the DC-jack power cable into DC-IN connector on the back of the monitor. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. (Optional ­ Requires a video card with DVI port) Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. 4 ­ Connect the female end of the power cord to the monitor's power adapter and connect the male end of the power cord to the AC outlet. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 2 Connecting Cables 1. 4. External Adapter 15-pin D-Sub Cable DVI Cable Power Cord 7 EN9110 INSTALLATION INSTRUCTIONS (cont) Preparing To Install The Optional Wall Mount Arm (Not Included) CONNECTIONS This monitor can be attached to a wall mounting arm you can purchase separately from Ergotron (www. ergotron. com). Turn the power OFF then disconnect the cables from the monitor before performing the procedure below. Lay the monitor face down on a soft surface. Remove the 4 screws holding the base to the back of the monitor. Remove the base. 8 EN9110 INSTALLATION INSTRUCTIONS (cont) Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. Insert the 4 screws into the holes and tighten. Refer to the user's manual that came with the optional wall mounting arm for instrucstions on attaching it to the wall. 9 EN9110 ADJUSTING THE VIEWING ANGLE INSTALLATION INSTRUCTIONS · For optimal viewing it is recommended to look at the full face of the · · monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5° to 20°. Figure 3 NOTES · Do not touch the LCD screen when you change the angle. It may cause · damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. 10 EN9110 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. [. . . ] Picture has color defects (white does not look white) Horizontal or vertical disturbances on the screen *Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO) *Adjust RGB color or select a pre-set color temperature from OSD. *Use win 95/98 shut-down mode Adjust CLOCK and FOCUS or perform hot- key (AUTO-key). CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. [. . . ]