User manual ENVISION G2016WA

[. . . ] TABLE OF CONTENTS FOR YOUR SAFETY --------------------------------------------------1 SAFETY PRECAUTIONS --------------------------------------2 SPECIAL NOTES ON LCD MONITORS -------------------3 BEFORE YOU OPERATE THE MONITOR ---------------------3 FEATURES --------------------------------------------------------3 PACKING LIST ---------------------------------------------------3 INSTALLATION INSTRUCTIONS ---------------------------4 CONTROLS AND CONNECTORS --------------------------5 ADJUSTING THE VIEWING ANGLE -----------------------6 OPERATING INSTRUCTIONS -------------------------------------7 GENERAL INSTRUCTIONS ----------------------------------7 HOW TO ADJUST A SETTING ------------------------------9 ADJUSTING THE PICTURE ----------------------------- 10-11 PLUG AND PLAY ----------------------------------------------- 12 TECHNICAL SUPPORT(FAQ) ----------------------------------- 13 ERROR MESSAGE & POSSIBLE SOLUTION -------- 14 APPENDIX -------------------------------------------------------------- 15 SPECIFICATIONS ----------------------------------------- 15-16 FACTORY PRESET TIMING TABLE ---------------------- 17 CONNECTOR PIN ASSIGNMENT ------------------------- 18-19 1 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 2 2 0. 75mm or H05VVH2-F2 3G 0. 75mm ) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 2 3G 0. 75mm ) shall be used. 5 CONTROLS AND CONNECTORS CONNECTING CABLES Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the D-sub Signal input socket on back of the monitor and connect the other end to the computer's D-Sub port. Connecting the Power Cord: Connect the power cord into your LCD monitor's power input socket, and then plug the other end into a 3-pin AC power outlet. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Connecting the DVI Cable (optional) : Connect one end of the 24-pin DVI cable to the DVI signal input socket on the back of the monitor and connect the other end to the computer's DVI port. Connecting the Audio Cable: Plug audio cable between the computer multi-media (or sound) card's audio output and monitor's audio input socket. Figure 2 1. 2 3 4 Power input socket DVI Signal input socket D-Sub Signal input socket Audio input socket Connecting Cables 6 ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5 to 20. Figure 3 NOTES Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. 7 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. Connect the cables according to instructions above (section Connecting Cables) Press the power button to turn on the monitor. The power indicator will light up. Figure 4 EXTERNAL CONTROLS 1. 7. External Control Button Source Auto Adjust button / Exit < / Volume > /Volume MENU / ENTER Power Button LED 8 FRONT PANEL CONTROL Power Button / Power Indicator: Press this button to turn the monitor ON or OFF. Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. [. . . ] *Computer Video Card should be snugly seated in its slot. *Make sure monitor's video cable is properly connected to the computer. *Inspect monitor's video cable and make sure none of the pins are bent. *Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. [. . . ]