User manual EPOX EP-LXA-M

[. . . ] LXA-M A Pentium® II Processor based AGP ® ® motherboard TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subject to change without notice. Manual Revision 2. 3 February 10, 1998 LXA-M Features FEATURES LXA-M Features: · LXA-M is based on the Pentium® II Processor operating at 233 ~ 333 MHz on Slot 1. The board is configured by an DIP Switch to match your CPU clock speed. · Designed with Intel's 82443 LX AGPset. [. . . ] (http://www. 2themax. com/ please visit our Technical Support section for the latest updates) · LXA-M utilizes a Lithium battery which provides environmental protection and longer battery life. Page 2 Features LXA-M · Supports the Universal Serial Bus (USB) connector. The onboard PIIX4 chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. · Built-in ATX 20-pin power supply connector. · Software power-down when using Windows® 95. · Supports ring-in feature (remote power-on through external modem, allows system to be turned on remotely. · Resume by Alarm - Allows your system to turn on at a preselected time. · Power Loss Recovery - In the event of a power outage your system will automatically turn itself back on without user intervention. · Supports CPU Hardware sleep and SMM (System Management Mode). · Supports Desktop Management Interface (DMI) facilitating the management of desktop computers, hardware and software components and peripherals, whether they are stand-alone systems or linked into networks. (option) · Built-in WOL (Wake-up On LAN) Connector. · Built-in SB-Link Connector. Page 3 LXA-M Installation INSTALLATION LXA-M Detailed Layout Bank 2 Bank 0 Bank 1 PS/2 USB (Top) CPU FAN Keyboard (Bottom) USB 1 USB 0 (Bottom) J5 CPU Cartridge SLOT 1 (Top) PWR FAN Parallel Port COM 2 COM 1 DIMM 1 DIMM 2 DIMM 3 ATX Power Input FDD1 IDE1 SW1 ON 1 234 Mouse J4 Battery Winbond 83977 I/Oset AGP SLOT 6 ALXA PCI Slot #1 PCI Slot #2 J7:WOL Flash Memory for BIOS J8 SB-Link 1 5 PCI Slot #3 PCI Slot #4 ISA Slot #1 ISA Slot #2 ISA Slot #3 Intel PIIX4 PCIset J3 IR CONN. J2 KEYLOCK J6 Chassis FAN Figure 1 Page 4 IDE2 POWER_ON 1 RESET SPK Secondary IDE Intel 443LX PCIset Installation LXA-M Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configure DIP Switch to match your hardware Install memory chips Device Connectors Configure DIP Switch 2theMax designs all motherboards with a DIP Switch to make your install fast and easy. The following will describe all of the DIP Switch that you are required to set before moving on to step 2. Note: The DIP Switch as depicted as shown (Figure 1) in their correct physical orientation. SW1 ON 1 2 3 4 1 ON SW1 2 3 ON ON ON ON Page 5 LXA-M Installation System Memory Configuration Memory Layout The LXA-M supports (3) 168-pin DIMMs (Dual In-line Memory Module). The DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized DRAM). · DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or 120MHz (8ns) bus speed. · If you use both 50ns and 60ns memory you must configure your BIOS to read 60ns. · When using Synchronous DRAM we recommend using the 4 clock variety over the 2 clock. [. . . ] IRTX + + IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is activate Turbo LED indicator - LED ON when higher speed is selected Power On/Off - This is connected to the power button on the case. Using the Soft-Off by Pwr-BTTN feature, you can choose either Instant Off (turns system off immediately), or 4 sec delay (you need to hold the button down for 4 seconds before the system turns off). When the system is in 4 sec delay mode, 2theMax has added a special feature to make the system go into suspend mode when the button is pressed momentarily. Page 9 [. . . ]