User manual EPOX KP6LA

[. . . ] KP6-LA A Pentium® II Processor based AGP motherboard TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subject to change without notice. Manual Revision 1. 2 August 15, 1997 KP6-LA Features FEATURES KP6-LA Features: · KP6-LA is based on the Pentium® II Processor operating at 233 ~ 330 MHz on Slot 1. The board is configured by an Easy-Setting-Single-Jumper (E. S. S. [. . . ] With Flash Memory you can always upgrade to the current BIOS as they are released. (http://www. 2themax. com/ please visit our Technical Support section for the latest updates) Page 2 Features KP6-LA · KP6-LA utilizes a Lithium battery which provides environmental protection and longer battery life. · Supports the Universal Serial Bus (USB) connector. The onboard PIIX4 chip provides the means for connecting PC peripherals such as; keyboards, joysticks, telephones, and modems. · Built-in ATX 20-pin power supply connector. · Software power-down when using Windows® 95. · Supports ring-in feature (remote power-on through external modem, allows system to be turned on remotely. · Supports CPU Hardware sleep and SMM (System Management Mode). · Supports Desktop Management Interface (DMI) facilitating the management of desktop computers, hardware and software components and peripherals, whether they are stand-alone systems or linked into networks. (option) · Supports LanDesk Client Manager (LDCM). (option) Page 3 Installation KP6-LA KP6-LA Detailed Layout Bank 2 Bank 1 Mou s e J9 1 J8 J7 PS/ 2 USB (Top) ATX Pow er Input Pow e r Su pply Fa n Mon itor in g CP U Fa n P ow er Bank 2 Bank 3 Ke yboa r d (Bottom ) USB 1 (Top) USB 0 (Bottom ) CPU Cartridge SLOT 1 CP U Hea t Se n s or in g Ch ip Parallel Port COM 2 COM 1 Bank 0 SIMM 1 SIMM 2 SIMM 3 SIMM 4 DIMM 1 DIMM 2 DIMM 3 FDD Connector Res er ve 3 3 0 MHz 3 0 0 MHz 2 6 6 MHz 2 3 3 MHz 2 0 0 MHz 1 Infr ar ed AGP SLOT PCI Slot # 1 PCI Slot # 2 PCI Slot # 3 PCI Slot # 4 IS A Slot # 1 J15 1 DIMM Volta ge JP6 1 Winbond 83977 I/ Oset In te l PIIX4 PCIs et JP5 1 Clea r CMOS JP7 J11 1 J12 1 JP12 JP11 JP10 JP9 De fa u lt J5 Pr im a r y IDE Seconda r y IDE JP8 PWR/ ON H/ D LED G/ LED SLEEP In te l 4 4 3 LX PCIs et J10 TBLED RS T 1 J13 SPEAK KEYLOCK LM7 9 Har d w a r e Mon itor KP6-LA Rev. # IS A Slot # 2 IS A Slot # 3 Figure 1 Ch a s sis P ow e r J14 JP3 JP2 1 Fla s h Mem or y for BIOS Page 4 Batter y KP6-LA Installation Easy Installation Procedure Easy Installation Procedure The following must be completed before powering on your new system: Configure Jumpers to match your hardware Install memory chips Device Connectors Configure Jumpers 2theMax designs all motherboards with the fewest jumpers to make your install fast and easy. The following will describe all of the jumpers that you are required to set before moving on to step 2. Note: The jumpers as depicted as shown (Figure 1) in their correct physical orientation. 1 BIOS Voltage Setting JP2: JP3: 1 JP2, JP3: = 1-2 - +5V Flash (Default) = 2-3 - +12V Flash JP5: 1 CMOS Clear JP5: = 1-2 - Run Mode (Default) = 2-3 - Clear CMOS 8 JP6: 2 7 DIMM Voltage Selection JP6: = 1-2, 3-4 - 3. 3V DIMM (Default) = 5-6, 7-8 - 5V DIMM 1 Page 5 Installation 16 15 CPU Processor Selection KP6-LA JP8: 2 JP9: JP10: JP11: JP12: = 1-2 - 200MHz = 3-4 - 233MHz (Default) = 5-6 - 266MHz = 7-8 - 300MHz = 9-10 - 330MHz = 11-12 - Reserved 1 = 13-14 - Reserved = 15-16 - Disable E. S. S. J. Reserved CPU Processor Selections JP9: = Reserved JP10: = Reserved JP11: = Reserved JP12: = Reserved JP8: Page 6 KP6-LA Installation System Memory Configuration Memory Layout The KP6-LA supports (3) 168-pin DIMMs (Dual In-line Memory Module) and (4) 72-pin SIMMs (Single In-line Memory Module). The DIMMs can be either EDO (Enhanced Data Out) or SDRAM (Synchronized DRAM). The 72-pin SIMMs must be installed in pairs, and DIMMs may be installed using just one chip. [. . . ] Now that your motherboard is installed you are ready to connect all your connections (figure 12). PS/2 Mouse (Top) PS/2 Keyboard (Bottom) J7: J8: J9: J10: J11: J12: J13: J14: J15: CPU Fan Power · A plug-in for the CPU Fan Power Power Supply Fan Monitoring · A plug-in for the Power supply so that BIOS can monitor the RPM's ATX Power Connector · 20-pin power connector Chassis Panel Connector · Keylock, Speaker, Reset, Turbo, Sleep, G/LED and HDD LED Primary IDE Secondary IDE Floppy Controller Chassis Fan Power · A plug-in for the chassis Fan Power Chassis open monitoring · A plug-in to monitor the chassis Page 9 654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 654321098765432109876543212109876543210987654321098765432121098765432109876543210987654321 USB 1 (Top) USB 0 (Bottom) Parallel Port (Top) Com1 (Bottom Left) Figure 12 Com2 (Bottom Right) Installation KP6-LA Device Connectors (continued) JP7 + JP9 + Power On/Off IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is activate Power Saving LED indicator - LED ON when system is in any power saving mode Sleep/Resume switch : Closed to enter sleep mode, a keystroke or mouse movement will instantly "wake up" the system. + Turbo LED indicator - LED ON when higher speed is selected + Reset - Closed to restart system. 1 Speaker - Connect to the system's speaker for beeping 1. GND KeyLock - Keyboard lock switch & Power LED connector 1. [. . . ]