User manual EPSON ACULASER CX11

[. . . ] ® Color Laser product No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U. S. ) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. [. . . ] If not, press the Copy button to enter the Copy mode. Press the u Up or d Down button several times until Contrast is selected. The current value next to Contrast is highlighted. Note: To increase or decrease the contrast, press the r Right or l Left button, respectively. The contrast increases or decreases one level at a time. Adjusting the RGB color You can adjust the image quality in RGB strength by selecting from 7 levels (-3 to 3) for red (R), green (G), and blue (B). The higher the level, the richer the image. For adjusting the image quality, see also "Adjusting the density" on page 237 and "Adjusting the contrast" on page 238. Note: RGB adjustment is available only for color copies. Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. 238 Copying 2. Press the u Up or d Down button several times until your desired color (R, G, or B) is selected. The current value next to R, G, or B is highlighted. Note: To increase or decrease the color strength, press the r Right or l Left button, respectively. The color density increases or decreases one level at a time. 7 7 7 7 7 7 7 7 7 7 7 7 Specifying the zoom ratio You can specify a zoom ratio by selecting from the fixed zoom ratios, or by specifying a value from 25 to 400% in increments of 1%. Make sure that the product is in Copy mode. If not, press the Copy button to enter the Copy mode. Place your original either on the document table or in the Auto Document Feeder (fax model only). For details, see "Setting Your Originals" on page 154. Specify your desired zoom ratio with either of the following methods. Selecting a zoom ratio: Press the l Left or r Right button several times until the desired fixed zoom ratio is displayed. The following document fixed zoom ratios are available: Zoom Ratio Settings LGL > LT Zoom 78% Copying 239 Zoom Ratio Settings A4 > B5 100% B5 > A4 HLT > LG Zoom 86% 100% 115% 154% Setting a zoom ratio: You can also specify a magnification rate between 25% and 400% using the numeric keypad. Note: If the l Left or r Right button is pressed after entering a magnification rate using the numeric keypad, the closest fixed value to the entered rate is displayed. Full-page copy The full-page copy function is used to slightly reduce the output in order to fit the document into the guaranteed print area of the product. [. . . ] Press the x B&W Start or x Color Start button to start the transmission. 478 Notices Paper Sources When Receiving Faxes When paper is loaded in both the MP tray and the optional paper cassette, the paper in the optional paper cassette is used when receiving faxes. D D D D D D D D D D D D Printing Fax Sender Information If the date, time, sender's phone number and other information are not printed, use the control panel to set Printer Sender Info to On. For details, see "Changing outgoing faxes settings" in "Making Changes to Fax Settings" in the online User's Guide. Notices 479 Glossary buffer See memory. character set A collection of letters, numbers, and symbols used in a particular language. ColorSync Macintosh software that is designed to help you get WYSIWYG (what you see is what you get) color output. This software prints colors as you see them on your screen. default A value or setting that takes effect when the product is turned on, reset, or initialized. download To transfer information from the computer to the product. dpi (dots per inch) The number of dots per inch is a measure of printer resolution. The higher the number of dots, the higher the resolution. driver See printer driver. drum The part of the product mechanism where the image is formed and transferred to paper. FF (Form Feed) A control code to break the page. fixed-width font A font whose characters are allotted the same amount of horizontal space, no matter the width of the character. [. . . ]