User manual EPSON EMP-83

[. . . ] In the case of a VCR, press the PLAY button. An image will be projected. Tip If a laptop computer or a computer with a LCD screen has been connected to the projector, you may need to change the output destination for video signals depending on the computer keys (the symbols and are indicated above the keys) or the computer's settings. The output destination can normally be changed by holding down the computer's key and pressing one of the Function keys. Once the source has been changed, after a short wait the projector will start projecting. [. . . ] If the output has been changed to external output, only the external output should be used. For details, refer to the documentation provided with your computer. If images do not appear . . . Change the input signal. Each time the is pressed, the video source cycles between Computer/Component Video, S-Video, and Video. Projector Remote Control If you have other problems . . . Refer to the online Help information. Examples of changing output NEC Panasonic TOSHIBA IBM SONY FUJITSU Macintosh After restarting the computer, change the Control Panel monitor and sound settings so that Mirroring is active. Press or , and then follow the instructions. Projector Remote Control * Refer to Troubleshooting. Projecting Adjustment Pages 28-30 of Instruction Manual Adjusting the projection angle Use the foot adjust levers to adjust the projection angle for the projector. With the foot adjust levers released, lift the front of the projector. Tip If you change the projection angle, you may get keystone distortion in the images. You can use the , on the projector's control panel to correct keystone distortion. For fine adjustment See page 7. The front foot can be retracted by pulling the front foot adjust levers and lower slowly the front of the projector. Lower Higher Adjusting the image size and focus Focus adjustment Image size adjustment Push the W (Wide) side to increase the size. Push the T (Tele) side to reduce the size. Automatically adjusting computer images to the optimum settings Press on the remote control. The tracking, display position and synchronization will be automatically adjusted. Other adjustments Press on the remote control. The setting menu will be displayed on the projection screen, and you can then adjust settings such as brightness, contrast and sharpness. Using the on-screen menus Main menu Remote control Move up Select Move left Move down Return Move right Adjustment / Turning Off the Projector Adjustment Keystone Correction Page 29 of Instruction Manual If the images have keystone distortion . . . Press , on the projector's control panel to correct the keystone distortion. Tip A keystone correction reduces screen size. The keystone correction is stored in memory. You will need to readjust the image if the projector is moved to a different location or the projection angle is changed. If the images become uneven in appearance after keystone correction is carried out, decrease the Sharpness setting. When the top is too wide When the bottom is too wide Turning Off the Projector Pages 31, 32 of Instruction Manual Turn off the power for the equipment connected to the projector. The following choices are available. The default setting is the black screen. Functions for Enhancing Projection Troubleshooting Page 40 of Instruction Manual Viewing the Online Help This projector is provided with an online help function which can be used when you have a problem using the projector. Press or . Select the item to view. Press the on Projector Remote Control the projector's control panel. Press the on the projector's control panel. The selected item will appear on the screen. on the Pages 54-56 of Instruction Manual Checking the Indicators The projector is equipped with indicators that alert you to problems with projector operation. The following tables show what the indicators mean and how to remedy problems that they indicate. (Problem/Alarm Display) indicator Indicator status Lights red Problem and remedy High temperature inside projector (overheating). The lamp will turn off automatically and projection will stop. Wait for about 5 minutes without operating the projector. After 5 minutes have elapsed, disconnect the power plug and re-insert it. After re-inserting it, press the to turn the power back on. [. . . ] After 5 minutes have elapsed, disconnect the power plug and re-insert it. After re-inserting it, press the to turn the power back on. Remove the lamp and check if it is broken. If the lamp is not broken, reinstall it. [. . . ]