User manual EPSON EMP-TW620

[. . . ] About the Manuals and Notations Used Types of Manual The documentation for your EPSON projector is divided into the following two manuals. Refer to the manuals in the order given below. Safety Instructions/World-Wide Warranty Terms This manual contains information on using the projector safely, and also includes safety instructions, world-wide warranty terms booklet and a troubleshooting check sheet. Be sure to read this manual thoroughly before using the projector. [. . . ] Cool-down time is approximately 30 seconds. After cool-down is complete, the projector goes to standby mode. You cannot use the remote control or the projector's control panel during cool-down. If the main power switch at the rear of the projector is turned off before cool-down is complete, wait for the lamp to cool down (normally about one hour is required) before turning the power back on again. Green Orange Cool-down progress When the indicators provide no help If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem. Problems relating to images No images appear p. 37 Projection does not start, the projection area is completely black, the projection area is completely blue, etc. Moving images are not displayed p. 37 Moving images played on computer are not displayed. The message "Not Supported. " is displayed p. 38 The message "No Signal. " is displayed p. 38 Images are fuzzy or out of focus p. 38 Interference or distortion appear in images p. 39 Problems such as interference, distortion or black & white checked patterns appear. Image is truncated (large) or small p. 39 Only part of the image is displayed. Image colours are not right p. 40 The whole image appears purplish or greenish, images are black & white, colours appear dull, etc. (Computer monitors and LCD screens have different colour reproduction performance, so that the colours projected by the projector and the colours appearing on the monitor may not necessarily match, but this is not a sign of a problem. ) Images appear dark p. 40 Projection stops automatically p. 41 Problems when projection starts Power does not turn on Problems with the remote control The remote control does not work p. 41 p. 41 36 Problem Solving Problems relating to images No images appear Have you pressed the [Power] button?on the remote control or on the projector's control Turn on the main power switch at the rear of the projector. Disconnect the power cable and then reconnect it. p. 14 Check the circuit breaker to see if power is being supplied. Press on the remote control to cancel the blank function. Check that the power for the connected equipment is turned on. If the "Message" menu command has been set to "On", messages relating to the image signals will be displayed. "Settings" - "Display" - "Message" p. 32 If a composite video or S-Video signal is being inputÅ If projection does not occur when the "Video Signal" menu command is set to "Auto", select the signal format that matches the signal source. "Settings" - "Input Signal" - "Video Signal" p. 33 If the signal source is connected to the [InputA] port If projection does not occur when the "InputA" in the "Input Signal" menu command is set to "Auto", set the signal format that matches the signal that is being projected from the connected equipment. "Settings" - "Input Signal" - "Input A" p. 33 You can also press on the remote control to select the format. p. 15 If the VCR or DVD equipment is connected using a D4 SCART adapter Press to set the signal format to "D4/SCART". p. 15 When still no images appear and the DVD equipment is connected, change the setting at the DVD equipment to RGB output. Are the image signal format settings correct? Have the configuration menu settings been made correctly? Were the projector and computer connected while their power was already turned on?When a computer is connected Try resetting all of the current settings. p. 34 If the connection is made while the power is already turned on, the function (Fn) key that switches the computer's video signal to external output may not work. Turn the power for the computer that is connected to the projector off and then back on again. Moving images are not displayed Is the computer image signal set Set the image signal to output only externally. Computer documentation, under a title such as "External to output simultaneously both output" or "Connecting an external monitor" externally and to the LCD monitor? [. . . ] 26 Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 29 Trigger Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 31 [Trigger out] port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 49 Turning off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]