User manual EPSON ES-800C PRODUCT INFORMATION

[. . . ] 3 halftoning modes (A, B, and C) and 4 dither patterns (A, B, C, and D) for bi-level data (Halftoning mode A only in color line sequence mode) (2 downloadable dither patterns) Gradation: Brightness: Halftoning process: Enable/disable POWEli switch `RESET switch Transportation screw Option control connector / Gamma correction: 2 for CRT display 3 for printer 1 for user defined Ground termina Color correction: 1 type for CRT display 3 types for printer output, available in color line sequence mode only SCSI ID rotary switch SCSI interface connectors Interface: Light source: Reliability: Bidirectional parallel and SCSI Noble gas fluorescent lamps (3 lamps) Main unit: MCBF 100, 000 cycles of carriage movement Scanners 11&I92 ES-800C-1 ES-800C Dimensions and weight: Width: 368 mm (14. 5 inches) Depth: 577 mm (22. 5 inches) Height: 161 mm (6. 5 inches) Weight: about 12 kg (26 lbs) SCSI Specifications Interface type: Function: ANSI X3. 131-1986 standard The following functions are included. BUS FREE phase ARBITRATION phase SELECTION/ RESELECTION phase COMMAND phase (Logical Unit number is fixed to 0 and command link function is not supported. ) DATA phase Data in phase Data out phase STATUS phase MESSAGE phase (Includes MESSAGE IN phase and MESSAGE OUT phase) ATTENTION condition RESET condition Logic level: TTL level compatible Electrical Specifications Voltage: Frequency: Power consumption: Insulation resistance: 120 VAC, flO% 49. 5 to 60. 5 Hz Approx. 50 W (max) 20 m between AC power line and chassis at 500 VDC Environmental Conditions Temperature: Humidity: Operation: 40" F to 95" F (5" C to 35" C) Storage: 10' F to 150" F (-20" C to 60" C) Operation: 30% to SO%, without condensation Storage: 20% to 85%, without condensation Operating conditions: Ordinary office or home conditions. [. . . ] When this error occurs, try the scanning operation with your software over again. The scanner returns to normal when it receives correct commands. Normally you do not need to reset the scanner. Interface error The interface setup is wrong, or the scanner is not properly connected to the computer. When this error occurs, check the interface connection. Push the RESET button or turn the scanner off and then back on to reset it. Default settings The table below shows the default conditions when the scanner is initialized. Item 1 Default Fatal error This indicates one of the following problems: One or more fluorescent lamps needs to be replaced. The transportation screw is not released. There is a problem, such as an open cover, with the optional automatic document feeder. Check that the transportation screw is released and check the automatic document feeder; then push the RESET button. If the scanner still does not operate properly, try turning the scanner off and then back on. If the scanner still does not operate properly, or if this error occurs repeatedly, consult your dealer. Data format Resolution Size Reading area Color mode 1 bit/pixel/color 1 100 dpi 1100% 1850 x 1170 dots, no offset 1 Monochrome (standard) When the scanner is initialized, the scanner terminates the scanning operation, and the carriage returns to the home position (rear of the scanner). Scanners 1112i92 ES-800C-3 ES-800C Option error This indicates a problem such as a paper jam with an installed option unit. Check the option unit and correct the cause of the trouble. Options 1 Product Number Automatic Document 8813011 Feeder (ADF) Option Name 1 Description Self Test To run the self test, follow the instructions below: 1. Turn on the power while holding down the RESET button. Continue holding the RESET button until initialization is complete. (It takes approximately 10 seconds for self test initialization to complete. Watch for the LEDs to change in the sequence described below to tell that initialization is complete. ) Just after power on: Power LED (green) - O N Ready LED (green) - O F F Error LED (red) - OFF After a few seconds: Power LED (green) - O N Ready LED (green) - O N Error LED (red) - OFF After a few more seconds: Power LED (green) - O N Ready LED (green) - O F F Error LED (red) -ON Finally, all LEDS are lit 3. The self test mode begins, and the scanner operates automatically. [. . . ] 1 ESMAC 1 Includes scanner Plug-In Module Mac Interface Kit (PIM) and Desk Accessory (DA), cable, Epson Apple Scanner Driver, and image editing software. Bidirectional Parallel 1 8808012 1 Available separately from kit for customers who already have Interface Board for scanning software. Provides a the PC bidirectional port in the PC to connect to the parallel interface in the scanner. [. . . ]