User manual EPSON LX-400 ESCP MANUAL

[. . . ] Flashes when paper has not been fully ejected or a paper jam has occurred. Tear Off (Font) button** Advances continuous paper to the tear-off position. Feeds continuous paper backward from the tear-off position to the top-of-form position. Load/Eject button Loads a single sheet of paper. Ejects a single sheet of paper if a sheet is loaded. Loads continuous paper from the standby position. [. . . ] The numbers next to the lever indicate the thickness setting. 2. Use the table below to select the appropriate paper thickness. Paper type Lever position 0 0 1 2 3 1 2 to 4 Standard paper (single sheets or continuous) Multipart forms 2-sheet 3-sheet 4-sheet 5-sheet Labels Envelopes 3. Close the printer cover. 2-28 Using the Printer Multipart forms You can use continuous or single-sheet carbonless multipart forms of up to five parts (one original plus four copies). Before you print on the forms, set the paper thickness lever as described in the previous section. The following tips will help you get good results: t Use only continuous multipart forms that are joined by spot gluing or side-crimping. Never load continuous multipart forms joined by metal staples, tape, or continuous gluing. t Use only single-sheet multipart forms that are line-glued only at the top. Insert the forms glued edge first into the printer. t Use only multipart forms that are free of wrinkles and waves. t If you need to adjust the loading position, use your application software or change the loading position as described on "Adjusting the top-of-form position" on page 2-21. t When you use side-crimped continuous multipart forms, the copies may not align with the original. Hold the cut-sheet feeder in both hands and press on the latch levers. Fit the notches in the cut-sheet feeder over the mounting posts on the printer. Releasing the latch levers locks the cut-sheet feeder in place. latch lever 2-32 Using the Printer 5. Slide the left edge guide so it is aligned with the triangle mark. Next, slide the right edge guide to roughly match the width of your paper. Slide the paper support midway between the edge guides. 2 6. Pull the paper-set levers all the way forward until the edge guides retract and lock open to allow for paper loading. Using the Printer 2-33 7. Next, tap the side and bottom of the paper on a flat surface to even up the stack. c Caution: Do not use envelopes, multipart forms, carbon paper, or labels in the cut-sheet feeder. 8. Insert up to 50 sheets of paper along the left edge guide. Adjust the position of the right edge guide so that it matches your paper's width. Make sure the position of the guide allows the paper to move up and down freely. [. . . ] 23 W (ISO/IEC 10561 letter pattern) Power consumption Note: Check the label on the back of the printer for the voltage of your printer. Environmental Temperature Humidity (without condensation) 10 to 80% RH 0 to 85% RH Operation Storage 5 to 35 °C ­30 to 60 °C Paper Note: t Use recycled paper, envelopes, labels, and single-sheet multipart forms only under normal temperature and humidity conditions, as follows: Temperature Humidity 15 to 25 °C 30 to 60% RH t Do not load paper that has been folded or is damaged, wrinkled, or curled. A-8 For LX-300+ Single sheets (standard): paper guide and cut-sheet feeder entry Width Paper guide: 100 to 257 mm Cut-sheet feeder: 182 to 216 mm Paper guide: 100 to 364 mm Cut-sheet feeder: 257 to 356 mm Paper guide: 0. 065 to 0. 14 mm Cut-sheet feeder: 0. 07 to 0. 14 mm Paper guide: 52 to 90 g/m² Cut sheet feeder: 64 to 90 g/m² Length Thickness A Weight Single-sheet multipart forms: paper guide entry Width Length Copies Thickness Weight Binding 100 to 257 mm 100 to 364 mm 1 original + up to 4 copies 0. 12 to 0. 39 mm 40 to 58 g/m² Line glued at the top of form A-9 Envelopes: paper guide entry Size Thickness Weight No. 10: 241 × 105 mm 0. 16 to 0. 52 mm 45 to 90 g/m² Continuous paper (standard and multipart): rear and bottom entry Width Length (one page) Copies Thickness Weight (not multipart) 101. 6 to 254. 0 mm 101. 6 to 558. 8 mm 1 original + up to 4 copies Printable area 0. 065 to 0. 39 mm Gathering area up to 0. 9 mm 52 to 82 g/m² Weight 40 to 58 g/m² (one sheet of multipart) Binding Spot glued or crimp bound on both sides A-10 Labels: bottom entry Label size Backing sheet width Backing sheet length (one page) 23. 8 × 63. 5 mm 2. 5 mm corner radius, minimum 101. 6 to 254 mm 101. 6 to 558. 8 mm Backing sheet thickness 0. 07 to 0. 09 mm Total thickness Label weight 0. 16 to 0. 19 mm 64 g/m² Roll paper: rear entry with optional roll paper holder Width Thickness Weight 216 ± 3 mm 0. 07 to 0. 09 mm 52 to 82 g/m² A A-11 For LX-1170 Single sheets (standard): paper guide and cut-sheet feeder entry Width Paper guide: 148 to 420mm Cut-sheet feeder: 182 to 420mm Paper guide: 100 to 364mm Cut-sheet feeder: 210 to 364 mm Paper guide: 0. 065 to 0. 14 mm Cut-sheet feeder: 0. 07 to 0. 14 mm Paper guide: 52 to 90 g/m² Cut sheet feeder: 64 to 90 g/m² Length Thickness Weight Single-sheet multipart forms: paper guide entry Width Length Copies Thickness Weight Binding 148 to 420mm 100 to 364 mm 1 original + up to 4 copies 0. 12 to 0. 39 mm 40 to 58 g/m² Line glued at the top of form A-12 Envelopes: paper guide entry Size Thickness Weight No. 10: 241 × 105 mm 0. 16 to 0. 52 mm 45 to 90 g/m² Continuous paper (standard and multipart): rear and bottom entry Width Length (one page) Copies Thickness Weight (not multipart) 101. 6 to 406. 4 mm 101. 6 to 558. 8 mm 1 original + up to 4 copies Printable area 0. 065 to 0. 39 mm 52 to 82 g/m² A Weight 40 to 58 g/m² (one sheet of multipart) Binding Spot glued or crimp bound on both sides Labels: bottom entry Label size Backing sheet width Backing sheet length (one page) 23. 8 × 63. 5 mm minimum 2. 5 mm corner radius, minimum 101. 6 to 406. 4 mm 101. 6 to 558. 8 mm Backing sheet thickness 0. 07 to 0. 09 mm Total thickness Label weight 0. 16 to 0. 19 mm 64 g/m² A-13 Roll paper: rear entry with optional roll paper holder Width Thickness Weight 216 mm 0. 07 to 0. 09 mm 52 to 82 g/m² Printable area Single sheets and envelopes: A B A B printable area printable area C B C For LX-300+ A B The minimum top margin is 4. 2 mm. The minimum left and right margins are 3. 0 mm each. [. . . ]