User manual EPSON OPTRA E312

[. . . ] Bk Page 1 Thursday, February 8, 2001 2:19 PM Edition: June 2000 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. pROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND , EITHER EXPRESS OR IMPLIED , INCLUDING , BUT NOT LIMITED TO , THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This publication could include technical inaccuracies or typographical errors. [. . . ] The printer stops and displays this light sequence for each piece of media you want to print. € Load media, with the side to be printed facing the front of the printer, into the manual feeder and push the operator panel button to resume printing, or • reset the printer by pushing the operator panel button with a long button press. If your printer lights look like this: Then your printer: is alerting you that the printer is out of paper/envelopes or that the paper did not feed properly from the automatic paper feeder. € Load media into the automatic paper feeder and push the operator panel button to resume printing or • reset the printer by pushing the operator panel button with a long button press. 46 Chapter 4: Troubleshooting LA. Bk Page 47 Thursday, February 8, 2001 2:19 PM If your printer lights look like this: Then your printer: top cover is open or the print cartridge is not installed. € Close the cover to display the light sequence that appeared before the cover was opened. If your printer lights look like this: Then your printer: flash memory is full (Memory Full) • Print data without saving it in flash memory by pushing the operator panel button with a brief button press or • • reset the front panel by pushing the operator panel button with a long button press. Bk Page 48 Thursday, February 8, 2001 2:19 PM If your printer lights look like this: Then your printer: • memory is full, or • received a page that is too complex to print, or • reduces the resolution of a formatted page to 300 dpi before printing, or • has a PPDS font error, or • doesn’t have enough memory to save what is in the buffer (resource save off), or • doesn’t have enough memory to defragment flash memory (insufficient defrag memory), or • cannot communicate with the host computer (host interface error). Each of the errors described above has a unique, secondary error code. Display the secondary error code by double-clicking the operator panel button. 48 Chapter 4: Troubleshooting LA. Bk Page 49 Thursday, February 8, 2001 2:19 PM Secondary error codes If your printer lights look like this when you double-click the operator panel button: Then your printer: memory is full (Memory Full). € Reduce the complexity of the job and/or the resolution, or • press the operator panel button with a brief button press to resume printing, or • reset the printer by pushing the operator panel button with a long button press. Bk Page 50 Thursday, February 8, 2001 2:19 PM If your printer lights look like this when you double-click the operator panel button: Then your printer: has received a page that is too complex to print (Complex Page). € Switch the printing mode to a different printing mode via the Lexmark driver for Windows, or • press the operator panel button with a brief button press to resume printing, or • reset the printer by pushing the operator panel button with a long button press. 50 Chapter 4: Troubleshooting LA. Bk Page 51 Thursday, February 8, 2001 2:19 PM If your printer lights look like this when you double-click the operator panel button: Then your printer: is out of memory while formatting a page and is forced to reduce the resolution to 300 dpi before printing it (Resolution Reduction Warning). € Push the operator panel button to resume printing, or • reset the printer by pushing the operator panel button with a long button press. Bk Page 52 Thursday, February 8, 2001 2:19 PM If your printer lights look like this when you double-click the operator panel button: Then your printer: has received a request for a PPDS font which is not installed (Font Error). € Reset the front panel by pushing the operator panel button with a long button press. 52 Chapter 4: Troubleshooting LA. [. . . ] Clears the printer buffer and all temporary settings, and returns to the initial power-on state. A measure of the sharpness of a printed image, expressed in the number of dots per inch (dpi). The material that adheres to the paper or other media to create the printed page. Fonts that use a single font outline for both screen display and printing. [. . . ]