User manual EPSON PERFECTION V30

[. . . ] 950 FCC part 15 subpart B class B CSA C108. 8 class B USB Interface Interface type Connector type Electrical standard Universal Serial Bus Specification Revision 2. 0 One receptacle (Type B) Full Speed mode (12 Mbps) and High Speed mode (480 Mbps), Universal Serial Bus Specification Revision 2. 0 Readable area Scanning Transparencies and Film Before scanning transparent documents, you need to remove the scanner's reflective document mat; this exposes the scanner's transparency unit (light source), which is built into the lid. If you're scanning slides or film strips, you'll also need to use one of the film holders. Connector pin arrangement Pin number 1 2 3 4 Signal VCC ­DATA +DATA GND Connector FireWire Interface Interface type IEEE 1394a-2000 compatible 2 - EPSON Perfection 3200 Series 11/02 EPSON Perfection 3200 Series Using the Transparency Unit To use the transparency unit, remove the reflective document mat by grasping the top of the mat and sliding it up gently, as shown. Using Film Holders Film has two sides, a shiny base side and a dull emulsion side. The base side of the film has the film maker's name and film ID numbers printed on it. [. . . ] The base side of the film has the film maker's name and film ID numbers printed on it. To scan 35-mm film strips, 4 × 5-inch film, or 120/220 (6 × 9cm) film, place the film in the correct holder: remove mat by sliding it up transparency unit 35-mm strips Make sure the cable for the tranparency unit is plugged into the round connector. If not, turn off the scanner, then connect the cable as shown. You may need to raise the scanner cover and twist the cable to insert it. 4 × 5-inch and 120/220 (6 × 9-cm) film Place the holder with the film onto the scanner. Make sure the white triangle on the holder points to the upper-right corner of the scanner's document table. make sure that the arrow faces up 11/02 EPSON Perfection 3200 Series - 3 EPSON Perfection 3200 Series Note: If you're scanning 35-mm slides, set the holder on the scanner first, then place the slides in the holder. EPSON Smart Panel opens on your computer. 3. Click the option of your choice to scan: Copy: Make a quick copy, or several copies, of your document. Printing with EPSON color ink jet printers is recommended. Photo Print: Make prints from your photos, negatives, and slides. On many Smart Panel screens, you'll need to click Finish to continue scanning and Launch to start other programs. See your on-screen Smart Panel User's Guide for detailed instructions. In Windows® XP, click Start > All Programs > EPSON Smart Panel > EPSON Smart Panel. Note: The ] Start button does not support OS X. EPSON Smart Panel is available as a Classic application only. In Windows XP, you may see a message the first time you press the ] Start button. Select Smart Panel for Scanner, click Always use this program for this action, then click OK. 4 - EPSON Perfection 3200 Series 11/02 EPSON Perfection 3200 Series Selecting EPSON Scan Settings If you need to manually adjust the settings in EPSON Scan, follow the guidelines shown at right. The illustration shows EPSON Scan (in Professional Mode) with the preferred order in which settings should be adjusted. Detailed descriptions are given in the electronic Reference Guide. Tip: The most important thing to remember when scanning is to select the correct image type and resolution for your scan. 1 Select basic settings: Document Type Document Source Image Type Resolution Target Size 3 Customize your exposure and use color management 4 Scan the image into your application 2 Preview your image 5 Close EPSON Scan Indicator Light The indicator light (next to the ] Start button) indicates the status of the scanner, as described below. Light On Flashing Flashing Color Green Green Red Status The scanner is ready to scan images. [. . . ] Select Smart Panel for Scanner, click Always use this program for this action, then click OK. 4 - EPSON Perfection 3200 Series 11/02 EPSON Perfection 3200 Series Selecting EPSON Scan Settings If you need to manually adjust the settings in EPSON Scan, follow the guidelines shown at right. The illustration shows EPSON Scan (in Professional Mode) with the preferred order in which settings should be adjusted. Detailed descriptions are given in the electronic Reference Guide. Tip: The most important thing to remember when scanning is to select the correct image type and resolution for your scan. 1 Select basic settings: Document Type Document Source Image Type Resolution Target Size 3 Customize your exposure and use color management 4 Scan the image into your application 2 Preview your image 5 Close EPSON Scan Indicator Light The indicator light (next to the ] Start button) indicates the status of the scanner, as described below. Light On Flashing Flashing Color Green Green Red Status The scanner is ready to scan images. [. . . ]