User manual EPSON POWERLITE ELPMBUNI INSTALLATION GUIDE

[. . . ] - 14 Securing the Upper Assembly Ceiling Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 15 Low-Profile Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 16 Securing the Projector to the Upper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 18 Final Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the projector and/or damage to the mounting surface. Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the projector and could increase the risk of fire. At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the projector. Recommended mounting surfaces: wooden studs, solid-flat concrete, and reinforced metal studs. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available). Page - 4 - Installation Manual ELPMBUNI Parts List NOTE: This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts (800-368-9700). Upper Assembly (Qty 1) Mounting Bracket (Qty 1) Plastic Barrel Caps (Qty 4) M3 Flat Washers (Qty 4) Note: Must be used with the M3 x 16 Phillips screws. Lag Screws (#14 x 2") (Qty 3) M4 x 12 Security Head Screws (Qty 4) NOTE: M3 x 16mm Phillips Head Screws (Qty 4) The following hardware is included in the hardware pack but is not required for the installation. M5 x 12mm Security Head Screws (Qty 4) M6 x 12mm Security Head Screws (Qty 4) Installation Tools Phillips Head Screw Driver Soft Material/ Blanket Allen Wrench (Supplied) Tape Measure Ladder NOTE: Portable Drill Pencil Level (Supplied) Stud Finder (Commercially Available) M5 Allen Wrench Mounting screws will vary by projector. Please see the following pages for model specific hardware: Pages 10, 11, 12, and 13. Installation Manual Page - 5 - ELPMBUNI ELPMBUNI Universal Mount Assembly A B C D E F G H I J K L M Single Wooden Stud Mounting Points Solid Structure Mounting Points Ceiling Plate Allen Wrench Height Adjustment Screws Tension Knobs Safety Knob Security Screws Leveling Barrels Universal Mounting Bracket Leg Assembly Projector (Not Supplied) Tri-Lock Opening Option 1 B A C E D F G K NOTE: The four (2-piece) leg assemblies can be used as single leg or any combination of single and dual legs together as shown in Options 1 and 2. The number of legs may vary depending on the number of mounting points found on the bottom of your projector. H M Combination Leg I J Single Leg L D Option 2 J M NOTE: See the best configuration for your projector for filter and lamp access. L Page - 6 - Installation Manual ELPMBUNI Projector Preparation WARNING: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the projector. THE PROJECTOR IS FRAGILE; HANDLE WITH CARE AT ALL TIMES. CAUTION: NOTE: Review the projectors manufacture's operation manual and refer to the ceiling installation instruction. Here you will normally find important reference information regarding installation dimensions such as (distance from the screen to the lens of the projector, top of the lens placement to the top screen etc. Adherence to these recommendations during your installation will enhance the quality of your final image on the screen. 1. 3. Carefully invert the projector and place it on a smooth flat surface. Identify the number of mounting points and screw thread (pitch) size. Most projectors have either three or four mounting points and are M4 in thread size (Figure 1). Mounting Points Inverted Projector Blanket, soft cloth etc Flat surface Figure 1 Installation Manual Page - 7 - ELPMBUNI 4. 5. Separate the upper assembly from the projector mounting bracket by slightly loosening the two tension knurl knobs to create free play between the bracket tri-lock assembly and the upper section tri-lock assembly points. Next loosen the safety screw knurl knob far enough to allow the two parts to be rotated 180° apart and separate. Upper Assembly Safety Knob Tension Knobs Figure 2 Figure 3 Tri-Lock Opening Rotate 180° To Unlock Figure 4 Page - 8 - Installation Manual ELPMBUNI Securing the Bracket to the Projector NOTE: The two-piece mounting legs are designed to allow routing of the legs around critical ventilation screens on the base of the projector as shown. You may also reduce the two-piece leg to a one-piece leg as shown for a better overall fit to the projector. 1. [. . . ] Tighten the remaining two tension knurl knobs until the mount becomes rigid. The safety knob should line up with the alignment slot on the mounting bracket (Figure 13). NOTE: Follow the number sequence prior to securing the projector to the upper assembly. The alignment slot must be in direct alignment with the safety knob to lock the mounting bracket to the upper assembly Safety Knurl Knob Insert universal bracket to the tri-lock, then rotate the projector 180° Tension Knurl Knobs Universal Mount Tri-Lock Opening Alignment Slot Projector Mount Figure 13 Page - 18 Installation Manual ELPMBUNI Final Adjustments 1. With the projector secured in the mount and power on and signal supplied to the projector you can now proceed with the final height, tilt, and roll and yaw to optimize the projected image. [. . . ]