User manual EPSON SPECTROPROOFER MOUNTER 24 BROCHURE

[. . . ] User's Guide NPD3701-00 EN SpectroProofer Mounter 24"/44" User's Guide Copyrights and Trademarks Copyrights and Trademarks No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer. Epson is not responsible for any use of this information as applied to other printers. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U. S. ) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions. [. . . ] Confirming the printer setup See the SpectroProofer Mounter 24"/44" Setup Guide Make sure to complete the printer setup (setting up the printer and installing the printer driver). Turn on the printer and make sure it is in the ready state. 2. Initial settings of SpectroProofer See "Making Initial Settings" on page 10 Performs the initial settings of SpectroProofer. 3. See the online help of the SpectroProofer Utilities for detailed information. Color calibration You can perform the color calibration to keep high print quality with reduced color difference. We recommend you perform the color calibration once every two weeks or once a month. A B Start the SpectroProofer Utilities. See "Starting SpectroProofer Utilities" on page 11 Click Printer Linearization. Starting SpectroProofer Utilities Follow the instructions below to start SpectroProofer Utilities. Windows Click Start, point to All Programs, point to SpectroProofer Utilities, and then click SpectroProofer Utilities. Mac OS X Double-click the hard disk icon, the Applications folder, the SpectroProofer Utilities folder, and then the SpectroProofer Utilities icon. C Follow the wizard to perform color calibration. Click the Help button to see the online help for detailed information. 11 SpectroProofer Mounter 24"/44" User's Guide How To Use Preparing and executing a color measurement job This section introduces the color measuring procedures using Preparing and executing a color measurement job. See the online help for detailed information. E Select the job you want to perform. A Turn on the printer. Make sure the printer and this product are both in the ready state. Make the initial settings when you use this product for the first time. See "Making Initial Settings" on page 10 Perform maintenance if necessary. See "Cleaning the Associate Parts for ILS20EP/ILS20EPUV" on page 13 Note: The ICC profile cannot be created by the SpectroProofer Utilities alone. You need a creation software separately. Follow the wizard to complete the settings. Click the Help button to see the online help for detailed information. B Set the paper in the printer. See the SpectroProofer Utilities online help for the supported media. Please refer to the User's Guide of the printer when you set the paper. C D Start the SpectroProofer Utilities. See "Starting SpectroProofer Utilities" on page 11 Click Preparing and executing a color measurement job. 12 SpectroProofer Mounter 24"/44" User's Guide Maintenance Maintenance Cleaning the Associate Parts for ILS20EP/ILS20EPUV If the color measurement value indicates abnormal value, clean the product. To maintain a good condition of the product, we recommend you to care for once a month. C Remove the white calibration tile from the white calibration tile holder. D Remove the backing from the printer. Cleaning procedures Clean the following three parts: the backing surface the surface of the white calibration tile the lens of ILS20EP/ILS20EPUV The procedures are as follows. A B Remove ILS20EP/ILS20EPUV and the mounter from the printer. See "Removing the Mounter" on page 15 Remove the white calibration tile holder from the printer. c Caution:the backing is a fragile part, do Because not drop the backing while removing it. E Use a dry, soft cloth to carefully remove any dust or dirt from the surface of the white calibration tile or the surface of the backing. If the dirt does not come off, clean it using a soft, clean cloth dampened with water. Then, wipe it with a dry, soft cloth. 13 SpectroProofer Mounter 24"/44" User's Guide Maintenance F Use an air spray for OA equipment to blow the dust off the lens in ILS20EP/ILS20EPUV. Recertification for Color Measurement Device ILS20EP/ILS20EPUV We recommend to inspect ILS20EP/ILS20EPUV once a year. For detailed information, contact customer support services for assistance. If customer support for your area is not listed below, contact the dealer where you purchased your product. [. . . ] sales) or http://www. epson. ca (Canadian sales). Internet Support Visit Epson's support website at http://epson. com/support and select your product for solutions to common problems. You can download drivers and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Help for Users in Europe Check your Pan-European Warranty Document for information on how to contact EPSON Customer support. Speak to a Support Representative Dial: (562) 276-1300 (U. S. ), or (905) 709-9475 (Canada), 6 am to 6 pm, Pacific Time, Monday through Friday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply. [. . . ]