User manual EPSON STYLUS PHOTO 875DC

[. . . ] Color Ink Jet Printer EPSON PhotoQuicker User's Guide 4011923-00 XXX How to use this guide This guides provides basic information about EPSON PhotoQuicker and EPSON PhotoStarter. To print your photo data, launch EPSON PhotoQuicker as instructed on page 4 in this guide, then follow the instructions below to print. For detailed information about the software, click the Help button to open online help. Start EPSON PhotoQuicker d If you have started EPSON PhotoQuicker manually, load the photos: from a folder from a memory card from TWAIN d Select the task you would like to perform from the following list: print all photos select, modify and print photos copy and save all photos select, copy and save photos d Select the photos. d Select a paper size and print layout. d Make the printing settings. d Print your photos. Contents Introduction to PhotoQuicker . 18 Problems when Print All is selected . [. . . ] Follow the on-screen instructions, and then click Load. The photo data will load. 12 Troubleshooting Refer to the appropriate section if you encounter any problems using EPSON PhotoQuicker. Errors messages If error messages are displayed during operation, follow the appropriate instructions below to correct the problem. Error messages Unable to find the file. Cause The photo file has been moved or deleted during loading. The floppy disk or MO to be written to is locked. Solution Restart EPSON PhotoQuicker. Unable to create a file. Close EPSON PhotoQuicker, unlock the disk, and then restart EPSON PhotoQuicker. Restart EPSON PhotoQuicker. Unable to open the file. The photo file has been moved or deleted during loading. The floppy disk or MO to be written to is locked. Close EPSON PhotoQuicker, unlock the disk, and then restart EPSON PhotoQuicker. Restart EPSON PhotoQuicker. Unable to write to the file. The photo file has been moved or deleted during loading. The floppy disk or MO to which the data is to be saved is locked. Close EPSON PhotoQuicker, unlock the disk, and then restart EPSON PhotoQuicker. Increase the amount of space on the start-up disk. Save the data to a disk with sufficient space. Insufficient free disk space on the disk. There is insufficient space on the start-up disk. There is insufficient space on the disk to save the data. 13 Error messages Unable to complete the operation due to insufficient memory. Unable to output an image. Cause There is insufficient memory. Solution Install sufficient memory and try again. There is insufficient memory. An incorrect output destination was specified. Install sufficient memory and try again. Specify a correct output destination and try again. Install sufficient memory and try again. Restart the computer, unplug the printer and then plug it back in, then try again. Specify an appropriate printer. An incorrect printer is specified. A printer other than STYLUS PHOTO 875DC is selected in the Chooser (for Macintosh) or in the printer setup (for Windows). 15 Error messages Unable to find the specified object. Cause If the memory capacity of your computer is small, you may require more memory. The floppy disk or MO to be written to is locked. Solution Install sufficient memory and then try again. Unable to save the paper settings information. Close EPSON PhotoQuicker, unlock the disk, and then restart EPSON PhotoQuicker. Re-install EPSON PhotoQuicker. The destination folder has been moved or deleted. The file is damaged. Check the file to be loaded. Install sufficient memory and then try again. [. . . ] Note: EPSON PhotoStarter is automatically launched at system start up. Opening the Startup menu Follow the instructions in this section to open the Startup menu, where you can access the various EPSON PhotoStarter dialog boxes. For Windows Right-click the EPSON PhotoStarter icon bar, then click Initialization Settings. . located on the task 25 The Initialization Settings dialog box is displayed. For Macintosh 1. Click the Application menu at the right side of the menu bar on your desktop, and then click EPSON PhotoStarter from the menu that appears. 26 2. Click Settings in the Initialization Selection dialog box. The Initialization Settings dialog box is displayed. Registering applications Follow the instructions in this section to register applications and have them appear in the Initialization Selection dialog box. [. . . ]