User manual EPSON STYLUS PHOTO 875DCS

[. . . ] Printer Basics Printed on recycled paper with at least 15% post-consumer content. Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON printer. EPSON is not responsible for any use of this information as applied to other printers. [. . . ] USB RW Switcher lets you toggle between read-only mode and write-to-disk mode on your memory card. If you haven't installed EPSON USB RW Switcher, follow the instructions in your Start Here poster. 1. Eject the memory card and adapter from the printer's memory card slot (see page 40 for instructions). Windows: Click Start, point to Programs, EPSON USB RW Switcher, and select EPSON USB RW Switcher. Macintosh: Open the EPSON USB RW Switcher folder on your hard drive. Double-click the EPSON USB RW Switcher icon. The first time you start USB RW Switcher, you see one of the screens below: Macintosh Windows 55 TM TM If you have a Macintosh and an older Kodak, Minolta, or KonicaTM digital camera, your card may be corrupted when your try to upload photos to or erase photos from it. This problem occurs because of a conflict between Macintosh utilities and older digital camera software. You can't write to your card if you have this problem. To use your card again, just reformat it in your camera. 3. Click OK to enable write-to-disk mode, then insert the memory card and adapter in the printer's memory card slot. Use Windows Explorer or the Macintosh Find command to locate the photos you want to upload on your hard drive. Use Windows Explorer or search your Macintosh desktop for the your memory card "drive". (Windows identifies the card as a Removable Disk; your Macintosh may title it Unknown. ) 6. If you have an Epson camera, drag the photos from your hard drive to the following directory on your memory card: D:\Dcim\100epson (where D is the drive assigned to your card). If your camera was made by a different manufacturer, the location for photos on your memory card will be different. You must copy or move your photos to the correct folder on your memory card. Otherwise, you won't be able to view them in Image Expert. 7. To return to read-only mode, eject the memory card and adapter from the printer's memory card slot (see page 40 for instructions). Then do one of the following: s Windows: Click Start, point to Programs, EPSON USB RW Switcher, and select EPSON USB RW Switcher Macintosh: Double-click the EPSON USB RW Switcher icon in the EPSON USB RW Switcher folder (Macintosh). s 56 You see one of the screens below: Macintosh Windows 8. Click OK. 57 58 Maintaining Your Printer This section describes maintenance procedures to keep your printer working at its best and preparation steps for moving your printer. Follow the instructions here for: s s s s s cleaning the print head (below) replacing an ink cartridge (on page 63) aligning the print head (on page 66) cleaning the printer (on page 67) transporting the printer (on page 68) For more details, see your electronic Reference Guide, as described on page 9. Cleaning the Print Head If your printed image is unexpectedly light or faint, or dots are missing from the image, you may need to clean the print head. This unclogs the nozzles so they can deliver ink properly. Cleaning the print head uses ink, so clean it only if print quality declines. [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. [. . . ]