User manual EPSON STYLUS PHOTO TX659 STARTUP GUIDE

[. . . ] Always test samples of paper stock before purchasing large quantities or printing large jobs. Poor quality paper may reduce print quality and cause paper jams and other problems. If you encounter problems, switch to a higher grade of paper. Use papers under these conditions: Temperature: 59 to 77 °F (15 to 25 °C) Humidity: 40 to 60% RH Store printouts on EPSON Photo Quality Glossy Film and SelfAdhesive Sheets under these conditions: Temperature: 59 to 86 °F (15 to 30 °C) Humidity: 20 to 60% RH Printable area A B-L B-R A B-L B-R C envelopes C single sheets/index cards A: The minimum top margin is 0. 12 inch (3. 0 mm). [. . . ] You see a screen similar to this one: 2. Then click OK. Removing the Memory Card You should eject your memory card before you use EPSON USB RW Switcher to toggle between read-only and write-todisk mode. If you have a Macintosh or you're running Windows 2000 and have enabled write-to-disk mode, you should also eject your memory card before you turn off your printer or disconnect the USB cable. Use one of these procedures to eject the memory card: t If you're running Windows 98, press the card eject lever to eject the memory card and card adapter. t If you're running Windows 2000 and have not enabled write-to-disk mode, press the card eject lever to eject the memory card and card adapter. If you have enabled writeto-disk mode, left-click the Eject Hardware icon on the Windows taskbar and click Stop EPSON SP 875DC Storage. Then press the card eject lever to eject the memory card and card adapter. t If you have a Macintosh, select the memory card icon on your desktop. Wait until you see a message that the memory card can be removed from the card drive, and then press the card eject lever to eject the card and card adapter. Never remove the memory card or turn off power to either the printer or computer while the card access light is flashing. The computer and memory card reader are communicating, and removing the card or turning off power could corrupt memory card data. Closing EPSON PhotoStarter If you don't want to start Image Expert automatically when you insert the memory card in the printer's memory card slot, you can close PhotoStarter. Windows: Right-click the EPSON PhotoStarter icon on the Windows taskbar, and click End on the menu that appears. The first folder you see is your photo folder. You must copy or move your photos to the correct folder on your memory card. Otherwise, you won't be able to view them using the View PC Card Images button or View Images command in Image Expert. Use these EPSON ink cartridges within six months of installing them and before the expiration date on the package: t Black ink cartridge: T007201 (U. S. ); T007311 (Canada) (Standard Capacity) t Color ink cartridge: T008201 (U. S. ); T008311 (Canada) To ensure good results, use genuine EPSON ink cartridges and do not refill them. Other products may cause damage to your printer not covered by EPSON's warranty. 5. To return to read-only mode, eject the memory card from the memory card slot (see "Removing the Memory Card" on page 8). Windows: Click Start and point to Programs, EPSON USB RW Switcher, and select RW Switcher. Macintosh: Open the EPSON USB RW Switcher folder on your hard drive and double-click the EPSON USB RW Switcher icon. When you need new ink cartridges, contact your dealer or call EPSON Accessories at (800) 873-7766 or visit our web site at www. epsonsupplies. com (U. S. In Canada, please call (800) 873-7766 for dealer referral. Be sure you have a new ink cartridge before you begin. Once you start the ink cartridge replacement procedure, you must complete all the steps in one session. 9 - EPSON Stylus Photo 875DC 4/00 EPSON Stylus Photo 875DC Follow these steps to replace ink cartridges: 1. Make sure the printer is turned on and not printing (the Ppower light should be on, but not flashing). [. . . ] Right-click the EPSON Stylus Photo 875DC icon in the Printers window. Follow the instructions on the screen to print a test page. Select the most precise alignment pattern from the choices on the test page. Enter the number of the best aligned pattern following the instructions on the screen (pattern 8 is the current setting). [. . . ]