User manual ESCALADE SPORTS 2L-6798-01

[. . . ] 6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. Note: This unit is equipped with U-Bolts to fit GoalrillaTM and GoaliathTM basketball units with 4 x 4, 5 x 5, 6 x 6, and 6 x 8 poles. Select the U-Bolt by measuring your pole and referring to the "Hardware Identifier" in this manual. Attach a Black Bracket (#17) to pole 3" below top pivot point, as shown in Figure 1, using a U-Bolt (#18), two washers (#15) and two hex nuts (#16). [. . . ] Mount the Wire Safety Cage (#7) to the frame on the front of the Halogen Lamp Assembly (#1). Squeeze the cage slightly so the wire ends fit into the inside four corners of the frame. 8. Figure 4 9. Install a Serreated Washer (#19) onto Lamp Base (#3) and screw the threaded portion of the Lamp Base (#3) into the threaded end of Pole Section "A" (#8). Secure Lamp Base by tightening jam nut on Lamp Base (#3) against end of Pole Section "A" (#8). Attach Lamp Base (#3) and Light Junction Box to Lamp Mount Bar (#2) using two Washer Head Bolts (#4), two washers (#5) and two locknuts (#6). Slide the swaged (crimped) end of Pole Section "B" (#9) into the unthreaded end of Pole Section "A" (#8). Align the holes and insert a self tapping screw (#12) to secure. (You will need to use a wrench or a pair of pliers to firmly start the self tapping screw. ) 12. Slide Pole Section "C" (#10) into the end of Pole Section "B" (#9) and secure with a self tapping screw (#12). Note: It is very important to evenly space out the six plastic ties to keep the electrical cord secure. Secure the electrical cord to the pole with six plastic ties (#13) in the locations shown in Figure 6. Cut off excess plastic tie. 4 ATTACHING HOOP LIGHT TO POLE REQUIRES AT LEAST TWO CAPABLE ADULTS. When attaching the Hoop Light to the pole, stay clear of all overhead power, electrical, telephone wires, and obstacles. Any contact between the Hoop Light and any of these lines will result in immediate danger. WARNING: When mounting the Hoop Light to the basketball pole, be sure that no U-clamp either traps or squeezes the electrical cord. Make sure the electrical cord is free and placed outside of the U-clamps. Do not plug the Hoop Light into any electrical outlet or extension cord until the entire assembly procedure is complete. 14. With the help of at least one other adult, lift hooplight assembly up and insert Pole Section "C" (#10) on top of Pole Section "D" (#11). If necessary, align hooplight with basketball unit by loosening U-Bolts (#14) slightly Tighten U-Bolts (#14) when slightly. Secure the remaining electrical cord to the pole with two plastic ties (#13) in the locations shown in Figure 7. Cut off excess plastic tie. Figure 7 5 CAUTION: !Unplug lamp and allow to cool before touching surface of lamp. Do not assemble without the guard. !Lamp should remain at least 20 inches from any sort of flammable material. [. . . ] WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS shall repair or replace with a comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept. Or Write us at: Escalade® Sports, Inc. Box 889, Evansville, IN 47706 - Attn: Warranty Dept. Or E-mail us at: basketball@escaladesports. com Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. [. . . ]