User manual ESCALADE SPORTS 2L-6811-00

[. . . ] A4301 Express MODEL NO. OWNER'S MANUAL Read this manual carefully before starting assembly. Read each step completely before beginning each step. Please Do Not Return This Product To The Store! Contact Escalade Sports customer service department at: Phone: 1-866-556-2754 Toll ­ Free !E-mail: customerservice@escaladesports. com Mailing Address: (correspondence only) Escalade Sports PO Box 889 Evansville, IN 47706 ® Upper Limb Cam Limb Adjustment Bolt Riser Cable String Please visit our World Wide Web site at: www. escaladesports. com ON-LINE TROUBLE SHOOTING ON-LINE PARTS REQUESTS TECHNICAL ASSISTANCE Limb Adjustment Bolt FREQUENTLY ASKED QUESTIONS Lower Limb ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION 2L-6811-00 Escalade® Sports is an authorized licensee of PSE Archery, Tuscon, AZ Escalade® Sports products may be manufactured and/or licensed under the following patents. 5921227, 5901692, 5749351, 5718212, 5495843, 5392757, 5054462, 5040520, 5020507, 4957094, 4748962, 4739744, 4596228, 4546754, 4519374, 4515142, Additional patents may be pending. [. . . ] Minor adjustments to center the arrow may be made as follows: To move right: Loosen height adjustment screw and move rest right desired amount. Rotate height adjustment screw to its original location and retighten. Loosen tension adjustment screw and slide collar to remove play. Rotate tension adjustment screw to its original location and retighten. To move left: Loosen tension adjustment screw and move rest left desired amount. Rotate tension adjustment screw to its original location and retighten. Loosen height adjustment screw and slide collar to remove play. Rotate height adjustment screw to its original location and retighten. NEVER SHOOT THE BOW WITH AN ARROW OFF OF THE ARROW REST. FIGURE B2 SIGHT PIN ASSEMBLY Assemble sight pins to sight plate as shown in figure B3. NOTE: Hex nuts fit into recessed slot in sight plate. FIGURE B3 SIGHT PLATE AND QUIVER INSTALLATION Install quiver and sight to bow, as shown in figure C, with two #10-24 x 3/4" pan head screws and two spacers. NOTE: The quiver is mounted on top of the sight plate. FIGURE C SIGHT PIN ADJUSTMENT Loosen thumb nut shown above for adjustment. Move pin up or down in the slot to change height of arrow trajectory. Rotate pin clockwise or counterclockwise to change trajectory right and left. DRAW LENGTH ADJUSTMENT Eccentrics with interchangeable draw length modules. An outstanding feature of your bow is the interchangeable draw length module system (See Chart A). With this system, you can change the draw length of the bow without relaxing the bow. Chart A Modules Module No. Draw Length 23" 24" 25" WARNING BOTH LOWER NEVER PULL BOW STRING WITHOUT BOTH UPPER AND LOWER DRAW LENGTH MODULES ON WHEELS! WARNING IF MODULES ARE CHANGED, THE DRAW LENGTH IS CHANGED, AND ARROW LENGTH REQUIREMENTS CHANGE. TO CHANGE MODULES: 1. Using a hex wrench, remove the two module mounting screws that attach the module to the upper wheel. Remove module from the other side of the wheel. (See figure E) NOTE: If screw is behind cable, push cable aside in order to easily reach screw with the hex wrench. Repeat steps 1 & 2 to remove module from lower wheel. Put a new module in place of old module on the upper wheel. Replace both module mounting screws to secure module. [. . . ] Time should be taken to aim before releasing arrow. (Figure K) Figure G FIGURE I THE TARGET The target face shipped with this set should be mounted close to the ground and on something that will accept the arrow and hold it, will not cause the arrow to glance off, and will not damage the arrow. For example, use a large cardboard box stuffed with straw. CARE OF YOUR BOW 1. Periodically examine your bow for wear or damage. [. . . ]