User manual ESCALADE SPORTS 2L-6986-01

[. . . ] ChildLife Inc. Escalade Sports® P. O. Box 889 Toll Free Fax E-mail Home Page (800) GO-SWING or (800) 467-9464 (866) 873-3537 childlifecs@escaladesports. com www. childlife. com MANUAL 1 Assembly Instructions Maintenance Instructions Safety Information NOTE TO INSTALLER: After you have assembled and installed the play system, please give the customer the tools provided and Manuals l and 2. Denali Play System RB SA Pictured is a Denali (Beam model for 4 swings) with add-ons. Congratulations and thank you for purchasing a fine ChildLife® brand play system! Customer Copy (Manual 1 of 2) 2L-6986-01 TABLE OF CONTENTS Installation Table 1. Steps 1­38 Box Requirements for Denali play systems US CPSC Consumer Information Sheet Hardware Identification Ground Anchor Stake Locations Sequence of Steps Access Ladder for 5' 6" Deck Summit Climbing Ramp & Hand Grips Tic Tac Toe Bubble Window Summit Alpine Climber Triple Wave Slide Hideaway Wall Main Tower Floor Insert pages 3­27 page 28 page 29 page 30 page 31 page 32 page 33 page 34 page 36 page 37 page 38 page 40 page 42 page 43 Please read these very important messages! ChildLife's products are for residential use only. They are not intended for use in places of public assembly such as schools, parks, condominiums, churches, temples, and child care centers. [. . . ] The bolts pass first through the Metal Bracket, then through the Mounting Baluster into the Safety Nuts. Go back and securely tighten all eight Bolts and Safety Nuts used in this step. ATTACH THE BASE PIECE AND DIAGONAL BRACES TO THE END LADDER (SEE ILLUSTRATION 32) ILLUSTRATION 32 3 x 1/4 Carriage Bolts HARDWARE REQUIRED FOR THIS STEP · Two 2-1/2 x 1/4 Carriage Bolts · Two 3 x 1/4 Carriage Bolts · Two 4-1/2 x 1/4 Carriage Bolts · Six 1/4 Safety Nuts (in Box #8) (in Box #8) (in Box #8) (in Box #8) Diagonal Braces 4-1/2 x 1/4 Carriage Bolts There are two holes drilled at the bottom of each End Ladder rail to compensate for sloping ground. If you had to dig the bottom of the End Ladder into the ground to make the Top Ladder horizontal in Step 29, select the higher hole for attachment of the Base Piece. After installation, your Top Ladder should be as horizontal as possible. Find the Base Piece and Diagonal Braces for the End Ladder in Box #8. Bolt the Base Piece to the outside bottom of the End Ladder using two 4-1/2 x 1/4 Carriage Bolts and 1/4 Safety Nuts. Loosely bolt the bottom of the Diagonal Braces to the ends of the Base Piece. Use two 2-1/2 x 1/4 Carriage Bolts and 1/4 Safety Nuts. Note that the Diagonal Braces must bolt to the Base Piece on the same side as the End Ladder. Do not tighten fully yet. Base Piece 2-1/2 x 1/4 Carriage Bolts 20 Bolt the top of the Diagonal Braces to the End Ladder rail using two 3 x 1/4 Carriage Bolts and 1/4 Safety Nuts. The bolts travel first through the top of the Diagonal Brace, then through the End Ladder rail. Now go back and tighten the hardware at the bottom of the Diagonal Braces. STAKE THE SWING SUPPORT FRAME (SEE ILLUSTRATION 33) ILLUSTRATION 33 HARDWARE REQUIRED FOR THIS STEP · Six Stake Nails Find the two 16 Ground Anchor Stakes and the six Stake Nails. For Beam swing supports, they are in Box #12. For Ladder swing supports, they are in Box #8. Ground Level Use 3 Stake Nails Here Pound these into the ground with a heavy hammer at the locations marked with an "X" in Table 4 on page 31. Position Stakes 10 from the end of a Base Piece to avoid cracking the Base Piece. Such cracks would not be covered under our limited warranty. Drive the Stakes in until no more than 3­ 4 are exposed. Nail each Stake to the Base Piece using the 3 Stake Nails provided. Use the pre-drilled holes and three nails for each Stake. Now go to Step 32. 21 ILLUSTRATION 34 Step 32. [. . . ] Be sure to install all of any optional Ground-level add-ons you have purchased before going beyond Step 35. 42 APPENDIX 8 Main Tower Floor Insert Each Floor Insert is shipped in one box marked #S74. ILLUSTRATION A 2-1/2 Deck Screws STEP 1. INSTALL THE CENTER DECK SUPPORTS See Illustration A. Follow the instructions in Step 12 to install the brown Center Deck Supports. However, in this case, fasten them to the brown Bottom Rails, upon which the Floorboards will rest. [. . . ]