User manual ESCALADE SPORTS 2L-7027-00

[. . . ] Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable wrench may be substituted for the wrenches). Please Do Not Return This Product To The Store! Contact Escalade® Sports customer service department at: Phone: 1-866-873-3528 Toll ­ Free !E-mail: tabletennis@escaladesports. com Mailing Address (correspondence only): Escalade Sports PO Box 889 Evansville, IN 47706 Please visit our World Wide Web site at: www. escaladesports. com ON-LINE TROUBLE SHOOTING ON-LINE PARTS REQUESTS TECHNICAL ASSISTANCE FREQUENTLY ASKED QUESTIONS ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION 2L-7027-00 Escalade® Sports products may be manufactured and/or licensed under the following patents. 6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2005 EscaladeSports 1. Lay table top #1 painted side down, on a smooth, flat surface. [. . . ] SET A PIECE OF WOOD ON CASTER SOCKET AND HIT PIECE OF WOOD TO DRIVE CASTER SOCKET INTO U-SUPPORT. Insert casters #11 into caster sockets #12. See Figure 11. 11 15. CAUTION: AT LEAST TWO ADULTS ARE NEEDED TO MOVE TABLE HALF! 16. Prepare an area for the assembly of the second table top half. If necessary, move the first table top half aside with the aid of a helper. Place it in a location where it won't be disturbed or damaged. If setting on its side, place the bottom edge no less than 12 inches away from the wall. Also place carpet or pieces of the shipping carton down to protect table top edges. If floor is not carpeted, brace table top half with a heavy object to keep it from sliding. Figure 11 12 7 17. Repeat steps 1 through 12 on second table half. Gently tap caster sockets #12 into U-support #7 on second table half until flange on sockets touches the edge of the tube. DO NOT HIT CASTER SOCKETS TOO HARD WITH A HAMMER. Insert casters #11 into caster sockets #12 on second table half. Figure 12 7 CAUTION: AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE REMAINDER OF THE ASSEMBLY! 2 Second Table Half 6 Figure 13 Place This Half Against A Wall First Table Half You Assembled Second Table Half You Assembled 5 15 7 9 7 20. Make sure the legs on the first table top half (the half with the name panel #5) are open and hinges are locked. With one person on each side of the table, lift and set table half on its legs. Place table against a wall as shown above to help stabilize table top half while second half is being attached. Be sure there is enough room to connect second half. CAUTION: BE SURE THE FIRST TABLE HALF YOU ASSEMBLED (WITH NAME PANELS #5 ATTACHED) IS STABLE AND AGAINST A WALL. DO NOT LEAVE TABLE HALF STANDING UNATTENDED. 21. Place two hex bolts #9 and locknuts #15 on floor next to caster wheels (on both sides of the table half) so they will be handy for the next step. CAUTION: UNTIL THE TABLE HALVES ARE CONNECTED THEY WILL NOT STAND ON THEIR OWN. IT IS RECOMMENDED TO HAVE THREE PEOPLE TO CONNECT TABLE HALVES. TWO TO STABILIZE TABLE AND ONE TO BOLT TABLE TOGETHER. 22. With a person on both sides of the second table half, slide the second table half against the first table half. [. . . ] UNLEVEL FLOORS If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in different directions to find the best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer U-legs. KEY NO. HARDWARE IDENTIFIER 1/4-20 x 1-1/2 Hex Hd. [. . . ]