User manual ESCALADE SPORTS 2L-7038-03

[. . . ] MODEL NO. B 3200W Goalrilla II BASKETBALL SYSTEM OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. Some smaller parts may be shipped inside larger parts. [. . . ] Note: The bottom four nuts will be forever embedded in concrete. The top four nuts remain on bolts and are used for leveling. 6. Figure 2 Figure 2 Figure 4 5 Let concrete stand for a MINIMUM of 72 hours. ASSEMBLY INSTRUCTIONS (Day 5) IMPORTANT!Nylon washers (#5) adequately space painted parts at all pivot points. Neglecting the use of these washers will result in rusted parts. NOTE: All board arms are made of rectangular tubing. Tightening hardware too tight may damage tubing and make adjustment of system difficult. Using Allen Wrench (#45) provided, attach Post Brackets (#44) to outside of brackets on back of Post Assembly (#2). Secure with two Flat Head Screws (#46), two Flat Washers (#26) and two Locknuts (#33) in each Bracket (#44). See Figure 3. 46 44 2 2 44 26 33 26 46 Slide Actuator Sleeve (#15) over Actuator (#16) and place Actuator Cap (#13) on top. Slide Pivot Tube (#14) in hole near the top of Actuator until equal amounts stick out on both sides of Actuator. NOTE: If necessary, use a hammer or rubber mallet to tap in Spacer. 19 18 3 5 2. Figure 3 3. Lay Pole (#2) on its side on two padded saw horses. Secure Actuator (#16) to Pole (#2) using one bolt (#19), split lockwasher (#18), washer (#3) and two plastic washers (#5) to thread into each side of Actuator. Insert Pole Cap (#1) into top of Pole (#2). It may be necessary to use a hammer or rubber mallet to tap Cap in. 5 Figure 4 15 16 14 13 3 18 19 4. 2 1 2 8 3 5 11 Figure 5 Attach lower arm (#11) to Pole (#2), as shown in Figure 5, using a bolt (#8), two flatwashers (#3), four plastic washers (#5) and hex nut (#4). Note: make sure "Goalrilla" lettering is right side up. Do NOT tighten bolt (#8) at this time. 5. 5 5 3 4 6 8 10 5 3 5 Secure Actuator (#16) to Lower Arm (#11) using one bolt (#8), two flatwashers (#3), four plastic washers (#5) and one hex nut (#4). Tighten both bolts (#8) securing Lower Arm (#11). Note: Tighten bolts snug but, do not over tighten. If the two Tube Plugs (#10) are not already installed insert them into open ends of Lower Arm (#11). It may be necessary to use a hammer or rubber mallet to tap plug in. 7 6. 5 3 4 2 11 3 5 2 Figure 6 Attach Upper Arm (#6) to Pole (#2), as shown in Figure 7, using a bolt (#7), two flatwashers (#3), four plastic washers (#5) and hex nut (#4). Note: Tighten bolts snug but, do not over tighten. [. . . ] THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL OR WORKMANSHIP . Paint kits will be available to assist in normal maintenance. HANGING ON RIM WILL VOID THE WARRANTY: Rims are not warranted for any defects other than workmanship. Torn back plates, damaged springs, bent rings, damaged eyebolts, and torn or distorted rim supports result from hanging on the rim and are not warranted. [. . . ]