User manual ESCALADE SPORTS G01991

[. . . ] PARTS IDENTIFIER HARDWARE DESCRIPTION QTY. REQUIRED (EXTRA PIECES MAY BE INCLUDED) H1 H2 H3 H4 H5 H6 3/8"x1-1/2" BOLT 16 16 15 3/8"WASHER, BLACK FLAT 5/8"ROUND HEAD PHILLIPS SCREW 1/2"FLAT HEAD PHILLIPS SCREW 52 3/16"x3/4"FLAT HEAD PHILLIPS SCREW 8 LEG LEVELER 4 For Customer Service Call 800-426-1421 3 PARTS IDENTIFIER ASSEMBLY PARTS P2 P1 DESCRIPTION QTY P1 P2 P3 P4A P4B P5 P6A P6B P7 P8 P9 P10 P11 SOCCER TABLE SIDE PANEL END PANEL LEG LEG CROSS BAR 1 2 2 2 2 2 1 1 2 8 2 2 1 BALL CATCHER(LONG WIRE) BALL CATCHER(SHORT WIRE) CUP HOLDER HANDLE BALL ENTRY CUP BALL ENTRY SOCKET ELECTRONIC SCORER For Customer Service Call 800-426-1421 4 PARTS IDENTIFIER ASSEMBLY PARTS DESCRIPTION QTY P13 P14 P15 P16 WIRE CLIP ADAPTER HINGE L-SHAPED BRACKET 3 1 12 4 ASSEMBLY PARTS C1 C2 C3 C4 C5 C6 DESCRIPTION QTY 3 PLAYER ROD 2 PLAYER ROD 5 PLAYER ROD RUBBER BUSHING 4 2 2 16 26 5/32x1-1/4"BOLT (used to install men ) ROD BUSHING 16 For Customer Service Call 800-426-1421 5 PARTS IDENTIFIER ASSEMBLY PARTS DESCRIPTION QTY C7 BLUE MAN 13 C8 C9 RED MAN 13 5/32" LOCKING NUT 26 ACCESSORIES DESCRIPTION QTY A1 A2 SOCCER BALL 4 TOOL 1 For Customer Service Call 800-426-1421 6 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE SOCCER TABLE IMPORTANT: Please read through the instruction book before attempting assembly to familiarize yourself with all parts and assembly steps. 1 CUT CORNERS OF THE BOX TOP AND PLACE IT ON THE FLOOR TO PROTECT THE PARTS AS THE UNIT IS BEING ASSEMBLED. REMOVE ALL PARTS AND PLACE THE PRE-ASSEMBLED TABLE CABINET P1 UPSIDE DOWN. [. . . ] ATTACH THE LEG LEVELERS H7 AS SHOWN IN figure 4. FIGURE 4 H6 P6A STEP 5 P6B H3 H3 P13 6 THIS STEP REQUIRES TWO ADULTS!TURN THE ASSEMBLED TABLE OVER AND SET ON ITS LEGS. 7 ATTACH THE BALL ENTRY CUP P10 AND BALL ENTRY SOCKET P11 TO THE SIDE PANELS WITH SCREW H3. ATTACH THE CUP HOLDERS P7 TO THE TABLE ENDS WITH SCREW H4. SEE figure 5. For Customer Service Call 800-426-1421 9 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY STEPS 6, 7 P7 FIGURE 5 H4 P10 P11 H3 ROD INSTALLATION 8 START WITH THE GOALIE ROD C1. CHOOSE ONE SIDE OF THE TABLE AND START WITH THE HOLE ON THE LEFT. SLIDE THE ROD THROUGH THE BEARING ON SIDE PANEL P2 AND THEN SLIDE A RUBBER BUSHING C4 ONTO THE ROD. CHOOSE ONE COLOR MAN AND SLIDE THREE OF THE SOCCER PLAYERS ONTO THE ROD. THEN SLIDE ANOTHER RUBBER BUSHING C4 ONTO THE ROD AND PUSH THE ROD THROUGH THE BEARINGS ON THE OTHER SIDE PANEL P2. NEXT ATTACH THE SOCCER PLAYER TO THE ROD USING THE BOLT C5 AND NUT C9. CONTINUE SEQUENCE OF ROD ASSEMBLES FOR ALL REMAINING RODS. INSTALL RODS IN THE ORDER SHOWN IN figure 6. P8 WITH SCREWS H5 AS SHOWN IN For Customer Service Call 800-426-1421 10 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY 3 MAN RED 2 MAN RED 5 MAN RED 3 MAN RED FIGURE 6 3 MAN BLUE 5 MAN BLUE 2 MAN BLUE 3 MAN BLUE FIGURE 6A For Customer Service Call 800-426-1421 11 ASSEMBLY INSTRUCTIONS SOCCER TABLE ASSEMBLY 10 PLUG IN THE TWO WIRES TO THE BOTTOM OF THE SCORING UNIT P12. ATTACH SCORING UNIT P12 WITH THE SCREWS H3 ON THE TOP OF THE END PANEL AS SHOWN IN figure ??. NEXT PLUG IN THE ADAPTER P14 TO A SUITABLE 110/120 VOLT HOUSE CIRCUIT ONLY. THEN PLUG ADAPTER TO THE BACK OF THE UNIT. [. . . ] HIT THE RESET BUTTON TO START A NEW GAME. TURN UNIT OFF AND UNPLG UNIT NOT IN USE. NOTE: ELECTRONIC SCORER WILL NOT WORK PROPERLY UNLESS ATTACHED TO THE TABLE WITH BOTH GOAL WIRES PLUGGED IN. H3 P12 For Customer Service Call 800-426-1421 12 [. . . ]