User manual ESPRIT 728 PLUS

[. . . ] The enhanced control panel offers to you the same great features you have come to depend on with added reliability, improved lightning protection and a new innovative dialer circuit. You have selected a sophisticated, user-friendly control panel designed to meet all of your technological, performance and security requirements. 1. 1 About This Manual This manual provides all the information you will need to understand panel operation, features and functions. If you are familiar with other security control panels, we recommend that you read this manual at least once to familiarize yourself with panel features and programming. Please refer to the index for a complete list of this manual's contents. [. . . ] An open "Fire Zone" will generate the following: u The panel will send a fire loop trouble report (if programmed at address 500) to the Central. u A trouble indicator, key [11], and a fire zone indicator, key [3], will flash on the keypad. u The 728+'s fire alarm will generate an intermittent output signal and the 728EX+'s fire alarm will generate a pulsed output signal, regardless of the system's current arming status. u Alarms are always audible, regardless of other settings. "24 Hour" & Fire Zones 7. 5. 1Zone 4 (Enable/Disable) Feature Select Programming è Address 090, key [1] Default: Zone 4 Enabled If the ATZ feature is enabled and zone 3 has been set as a fire zone, zone 4 must be disabled if it is not going to be used. Key [1] "Off": Zone 4 Enabled Key [1] "On": Zone 4 Disabled [ENTER] + Installer Code + [10] [9] [10] + [1] On/Off + [ENTER] 7. 6 Feature Select Programming è Address 104 , keys [1] to [10] Using the "Feature Select Programming Method", select which zones will be defined as Instant Zones. If an "Instant" zone opens, the control panel will immediately generate an alarm after the "Zone Speed" has elapsed. Instant Zones 7. 7 Feature Select Programming è Address 108, keys [1] to [10] Using the "Feature Select Programming Method", select which zones will be defined as Follow Zones. Follow zones function as follows: u If a follow zone opens and no entry delay zones have been triggered; the control panel will immediately generate an alarm after the zone speed has elapsed. u If a follow zone opens during another zone's entry delay period, the control panel will wait until the end of the entry delay period before generating an alarm. u If a follow zone opens when more than one entry delay zone has been triggered, the panel will wait until the end of the entry delay zone that opened first before generating an alarm. Follow Zones 30 Zone Definitions 7. 8 Decimal Programming è Address 050 Default: 45 seconds Any zone that has not been identified as either Instant Zones, Follow Zones, Entry Delay 2, or "24 Hour" & Fire Zones (see above) will automatically default to Delay 1. You can program the Delay 1 period between 001 and 255 seconds into address 050. If a zone defined as Delay 1 opens in an armed system, the control panel will wait the pre-programmed period before generating an alarm. This provides the users the time required to disarm the system when entering the protected area. [ENTER] + Installer Code + [10] [5] [10] + 3-digit decimal value (001-255) + [ENTER] Entry Delay 1 7. 9 Feature Select Programming è Address 112, keys [1] to [10] Using the "Feature Select Programming Method", select which zones will be defined as Entry Delay 2 Zones. If a zone defined as Delay 2 opens in an armed system, the control panel will wait the Entry Time Delay 2 (see below) period before generating an alarm. This provides the users the time required to disarm the system when entering the protected area. 7. 9. 1 Entry Time Delay 2 Decimal Programming è Address 051 Default: 45 seconds This applies to all zones defined as Delay 2 (see Entry Delay 2 above). You can program the Delay 2 between 001 and 255 seconds. [ENTER] + Installer Code + [10] [5] [1] + 3-digit decimal value (001-255) + [ENTER] Entry Delay 2 7. 10 Feature Select Programming è Address 086, key [8] This feature divides the alarm system into two distinct systems, identified as "System A" and "System B". You can assign each zone to System A, System B, both systems, or neither system. Partitioning works as follows: u Zones assigned to System A, will arm/disarm when the system is "System A Armed/Disarmed". u Zones assigned to System B, will arm/disarm when the system is "System B Armed/Disarmed". u Zones assigned to both systems ("dual area") will arm when the system is either "System A Armed", "System B Armed" or when both systems are armed and will disarm only when both systems disarm. [. . . ] See Earth Ground B Back-up Battery . See Manual Zone Bypassing Bypass Enabled Zones . 13 Hexa Streamlined Section Programming. 14 I Input Terminal Connections for Single Zones . [. . . ]