User manual EUTECH INSTRUMENTS ALPHA PH 2000

[. . . ] Alpha pH 2000 Processor/Transmitter pH / ORP ROSS and the COIL trade dress are trademarks of Thermo Fisher Scientific Inc. AQUAfast, Cahn, ionplus, KNIpHE, No Cal, ORION, perpHect, PerpHecT, PerpHecTion, pHISA, pHuture, Pure Water, Sage, Sensing the Future, SensorLink, ROSS, ROSS Ultra, Sure-Flow, Titrator PLUS and TURBO2 are registered trademarks of Thermo Fisher. 1-888-pHAX-ION, A+, All in One, Aplus, AQUAsnap, AssuredAccuracy, AUTO-BAR, AUTO-CAL, AUTO DISPENSER, Auto-ID, AUTO-LOG, AUTO-READ, AUTO-STIR, Auto-Test, BOD AutoEZ, Cable-Free, CERTI-CAL, CISA, DataCOLLECT, DataPLUS, digital LogR, DirectCal, DuraProbe, Environmental Product Authority, Extra Easy/Extra Value, FAST QC, GAP, GLPcal, GLPcheck, GLPdoc, ISEasy, KAP, LabConnect, LogR, Low Maintenance Triode, Minimum Stir Requirement, MSR, NISS, One-Touch, One-Touch Calibration, One-Touch Measurement, Optimum Results, Orion Star, Pentrode, pHuture MMS, pHuture Pentrode, pHuture Quatrode, pHuture Triode, Quatrode, QuiKcheK, rf link, ROSS Resolution, SAOB, SMART AVERAGING, Smart CheK, SMART STABILITY, Stacked, Star Navigator 21, Stat Face, The Enhanced Lab, ThermaSense, Triode, TRIUMpH, Unbreakable pH, Universal Access are trademarks of Thermo Fisher. Guaranteed Success and The Technical Edge are service marks of Thermo Fisher. [. . . ] The display prompts you to place the sensor in the low concentration sample (relative value of 20%). Remove the electrode from the first standard, wash it well and then immerse it in the 20% standard. When the display stabilizes press the ENT key. The "CAL" indicator flashes and the controller adjusts its display to the 20% relative value and exits to the Measurement mode. Note: If there is a calibration error, the transmitter displays "ERR". In this case press the and keys simultaneously (escape) to restart the calibration, beginning from step 1. Note: If you stop calibration after entering the first value, or if calibration is defective, the controller will use its original calibration data. 5. 5 View actual zero and slope MEAS PH O C atc CAL ENT CAL ENT PH 1. While in Measurement mode press the CAL key. The display will prompt you to enter a security code. Leave the security code at "000" (view only mode). The display shows the slope in mV (upper value) and the pH reading at 0 mV (zero point, lower value). Note: If no key is pressed for 30 seconds the transmitter automatically returns to the Measurement mode. 3. Press the ENT key to return to the Measurement mode. 6 6. 1 SET-UP MODE Enter Setup mode In the Setup mode the controller can be configured to your individual requirements. While in Measurement mode press the ENT key. MEAS PH 2. The display prompts you to enter the security code. Set the security code with or key to: ­"SCD22" if you want to change parameter settings ­"SCD000" if you want to view only parameter settings (view only mode) O C ENTER ENT 3. Press the ENT key. ENTER ENT SETUP HOLD ENTER ENT SE TUP HOL D ENTER ENT Temperature settings see section 6. 3 SETUP HOLD ENTER ENT Relay A (set point 1) settings see section 6. 4 SETUP HOLD ENTER ENT Relay B (set point 2) settings see section 6. 4 SETUP HOLD ENTER ENT Controller settings see section 6. 5 SE TUP HOLD cur. 1 ENTER ENT Current output 1 settings see section 6. 6 SETUP HOLD cur. 2 ENTER ENT Current output 2 settings see section 6. 7 SETUP HOLD ENTER ENT Wash contact settings see section 6. 8 SETUP HOLD ENTER ENT Unit settings see section 6. 9 SETUP HOLD ENTER ENT CAL Calibration see section 5 Note: to exit Setup mode at any time press the and key simultaneously (escape). The controller returns to the Measurement mode. 6. 2 Electrode Offset (OFS) sub-function The electrode offset sub-function is only available if the controller is configured for pH measuring. Use this sub-function to set an offset that corrects the readings without removing the electrode from the control system. The controller will add or subtract the offset value from the measured pH and display the corrected value. However, if you need to offset the value beyond the average offset you would expect in your application type, consider a full calibration or even electrode replacement. Record the controller's pH reading at the time you take the sample. [. . . ] Thermo Scientific will not be responsible for damage resulting from careless or insufficient packing. A restocking charge will be made on all unauthorized returns. NOTE: Thermo Scientific reserves the right to make improvements in design, construction, and appearance of products without notice. 10. 4 Guidelines for Returning Unit for Repair Use the original packaging material if possible when shipping the unit for repair. Otherwise wrap it with bubble pack and use a corrugated box for additional protection. [. . . ]