User manual FAAC 400

[. . . ] THE 400 OPERATOR AND 455 D CONTROL PANEL: INSTALLATION MANUAL February, 2009 400 Operator And 455 D Control Panel Installation Manual CONTENTS Important Safety Information Technical Data Unpacking the Operator The 400 Compact Operator General Characteristics Installation Instructions Prepare the Gate Manual Release Mechanism Install the Operator Install the 455 D Control Panel Exploded View, 400 CBAC 400 Parts List The 455 D Control Panel General Description 2 4 5 6 6 6 7 7 10 12 13 14 14 14 15 15 16 18 20 22 22 22 23 24 26 26 27 28 The 455 D Control Panel Installation Instructions Installing the 455 D Control Panel Connect the Main Power Supply Connect the Operator to the Control Panel Check the Motor's Direction of Rotation Connect Other Devices Set Other Operating Controls Programming Learning of Operating Times Learning of Normal Times Learning Times with Gatecoder Automated Systems Test Logic Tables of 455 D Control Panel Maintenance Safety in Gate Design Troubleshooting Limited Warranty FAAC International, Inc. 303 Lexington Avenue Cheyenne, WY 82007 www. faacusa. com Page 2 February, 2009 400 Operator And 455 D Control Panel Installation Manual IMPORTANT SAFETY INFORMATION Both the installer and the owner and/or operator of this system need to read and understand this installation manual and the safety instructions supplied with other components of the gate system. This information should be retained by the owner and/or operator of the gate. Your gate must be properly installed and must work freely in both directions before the automatic operator is installed. [. . . ] DECODER CARD: If you are installing the Digicard magnetic card reader, or the Digikey keyboard, use the quick-fit connector J2 for the DS decoder card (see Figure 1). NOTE: If your using both a receiver and decoder, hard wire the decoder and plug in the receiver. OPEN/HOLD OPEN DEVICE: To open and hold open the gate, simply maintain a contact across terminals "OPEN DEVICES". ("A" Mode only) STOP BUTTON: The stop button you install must have normally closed (N. C. ) contacts. Multiple stop buttons must be wired in series. Connect your stop device between terminals 11 and 16. (This jumper is already provided form factory. NOTE: The 455 will not operate the motors without a closed circuit between 11 & 16. The LED Indicators: The nine light emitting diodes (LEDs) on the control panel can be used to check for the proper function of the devices attached to the panel. The LED lights are on whenever the contacts are closed across each of the respective terminals. OP_A and OP_B (Partial Opening) should illuminate only when an activating signal is sent for 2 and 1 gate leaves, respectively. STOP should be illuminated except when the stop button is pressed. FSWOP and FSWCL should be Cord grip or conduit from U. L. Listed gate operator(s) Op. 1 Op. 2 LED OP_A OP_B Stop FSW Open FSW Close FCA1 FCC1 FCA 2 FCC 2 On Command Given Command Given No Command Opening reversing devices clear Closing reversing devices clear Off No Command No Command Command Given Reversing device triggered Reversing device triggered Flashes when gate coder is in use. Operator 1 Flashes when gate coder is in use. Operator 2 F SW O P O P_ A ST O P O P_ B F SW C L F C A1 FSWOP FCA1 OP_A FCC1 STOP FCC2 OP_B FCC1 FCC2 F C A2 FSWCL FCA2 This display shows the normal status of the control panel. This display shows the meaning of each LED. Figure 12. The 455 D display. Page 18 February, 2009 400 Operator And 455 D Control Panel Installation Manual command to open and a command to close. A second command during opening stops the gate. A second command during closing reopens the gate. · EP (semi-automatic, step by step): This mode requires a command to open and a command to close. A second command during opening or closing causes the gate to stop. A third command then reverses the previous motion of the gate. [. . . ] If either does not illuminate, then one of your reversing devices is preventing the gate from responding to your signal. February, 2009 400 Operator And 455 D Control Panel Installation Manual Page 28 LIMITED WARRANTY To the original purchaser only: FAAC International, Inc. , warrants, for twenty-four (24) months from the date of invoice, the gate operator systems and other related systems and equipment manufactured by FAAC S. p. A. and distributed by FAAC International, Inc. , to be free from defects in material and workmanship under normal use and service for which it was intended provided it has been properly installed and operated. FAAC International, Inc. 's obligations under this warranty shall be limited to the repair or exchange of any part of parts manufactured by FAAC S. p. A. and distributed by FAAC International, Inc. [. . . ]