User manual FABER MIRROR

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FABER MIRROR. We hope that this FABER MIRROR user guide will be useful to you.

Lastmanuals help download the user guide FABER MIRROR.


FABER MIRROR : Download the complete user guide (5894 Ko)

Manual abstract: user guide FABER MIRROR

Detailed instructions for use are in the User's Guide.

[. . . ] Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc. EN 44 • If the extractor is used in conjunction with non-electrical appliances (e. Gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. [. . . ] € Repeat this operation on the other side, checking that the two marks are levelled. € Insert the bracket plugs 11a into the holes (1) and tighten the screws. 1 on the wall, about 1-2 mm from the ceiling or from the upper limit, aligning the centre (notch) with the vertical reference line. 1 on the wall at X mm below the first bracket (X = height of the upper chimney section), aligning the centre (notch) with the vertical line. € Fix the brackets using the 12a screws (4, 2 x 44, 4) supplied with the hood. 1 EN 99 Fitting the Hood canopy • Adjust the two screws Vr, in the brackets 11a, so that they are at the start of their travel (B). € Connect the Hood to the Mains Power Supply, inserting a bipolar switch with a contact aperture of at least 3mm. (See the paragraph on USE) • Open the Bottom Door by pulling it downwards with your hands. € From the inside of the hood body, turn screws Vr to level the hood body itself. Warning: should the rear wall not be completely flat and cause the two glass panels not to be aligned, pls turn on the two knobs in the lower part inside the hood body until you reach the per alignment of the two glass panels. (See the paragraph on USE) • Disconnect the hood from the mains power supply. Warning: Should the door encounter an obstacle while opening or closing it will block. When the obstacle is removed and the button is pressed again the door will open. 11a Vr (B) 11 Replacing the fuser • The fuser is placed up on the left side. Connections DUCTED VERSION AIR EXHAUST SYSTEM of When installing the ducted version, connect the hood to the chim using either a flexible or rigid pipe ø 150 or 120mm, the choice 10 which is left to the installer. To install a ø 150 pipe u • To install the dumper 10 • Fix the pipe in position using sufficient pipe clamps (not s plied). Cer To install a ø 120 pipe • To install a ø 120 mm air exhaust connection, insert the reduu flange 9 on the dumper 10. € Fix the pipe in position using sufficient pipe clamps (not s plied). ø 150 9 10 ø 120 EN 1 10 0 RECYCLING VERSION AIR OUTLET To install the hood in recycling version, the optional charcoal filter kit must be purchased. € Screw the filter cover onto the air outlet, using four screws 12c (2. € Fix the air outlet grid 8 on the recirculation air outlet using the 2 screws 12d (2, 9 x 9, 5) provided. 16 12d 8 12c ELECTRICAL CONNECTION • Connect the hood to the mains supply. [. . . ] Warning: During the Opening and Closing phase the panel has a guard device that reverses the direction of movement in the event of blockage during the movement itself. it performs a maximum of 6 attempts before the “ “ icon flashes to indicate actual blockage. At this point, remove the obstacle preventing movement if possible, then press and hold button L for 2 seconds. The panel will once again make a maximum of 6 attempts to close or open before reverting to blocked status if movement is not successful. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FABER MIRROR

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FABER MIRROR will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag