User manual FAGOR IF-900S

[. . . ] C60T379A2. qxd 14/3/07 16:10 Pgina 23 ES ES EN EN FR FR DE DE PT PT MANUAL DE UTILIZACIN MANUAL DE UTILIZACIN GUIDE TO INSTALLATION GUIDE TO INSTALLATION GUIDE D'UTILISATION GUIDE D'UTILISATION BETRIEBSANLEITUNG BETRIEBSANLEITUNG GUIA DE UTILIZAO GUIA DE UTILIZAO Placa de coccin Cooking Hob Table de cuisson Kochfeld Placa de cozinha C60T379A2. qxd 14/3/07 16:10 Pgina 23 C60T357A4. qxd 14/3/07 15:55 Pgina 1 MANUA LD EI NS TA L A N CI Y O US ARATO L AP DE C60T376A8. qxd 14/3/07 16:21 Pgina 1 APPLIA NCE IN ST AL LA ON TI D AN US MANUAL AGE C60T376A8. qxd 14/3/07 16:21 Pgina 2 COMMIT TO ECOLOGY, RECYCLING AND PACKAGING WITH US We work to protect the Environment. For this reason, our packaging: Is 100% recyclable. Has the smallest possible amount of parts and material to make recycling easier. WARNING Only the Authorised Technical Service can replace your hob plate if it breaks down. Otherwise your guarantee will not be valid. [. . . ] 1. Press the button The hob power display will display (bo) and the hob will start to give maximum power. 2. Once the hob has heated up, select the chosen power level by pressing the "-" button in zone "B". The "BOOSTER" function will be cancelled by pressing any other power sensor associated with the hob, or with the on/off sensor. IMPORTANT By using the "BOOSTER" function, if the other hob is switched on the same side of the hobplate, the maximum power level which can be used is 6. This is due to the fact that in this function the appliance takes power from the adjacent hob. 11 C60T376A8. qxd 14/3/07 16:21 Pgina 12 OFFSET PROGRAMMING This allows you to adjust the finishing time and the duration of this cooking session. Switch on the hob of your choice, using the button. Press the button and it will display the current time. If the time is correct, go to point 4, and if not, adjust the time. ADJUSTING THE CURRENT TIME: Use the "-" and "+" power buttons in zone (B) to change the hour and use the "-" and "+" timer buttons (E) to adjust the minutes. Validate the time by pressing the button (the digits will then flash). Adjust the time to when you wish cooking to finish with the " -" and "+" buttons from zones (B) and (E). Adjust the cooking time using the "-" and "+" buttons in zone (E). Define the chosen power level for cooking with the "-" and "+" buttons from zone (B). Validate the power by pressing the button. Once programmed, it displays (Auto) and then the digits go off and only a red dot remains lit. IMPORTANT Offset programming cannot be used at the same time on more than one hob. The chosen finishing, duration and power values must be changed whilst the digits are flashing. 12 C60T376A8. qxd 14/3/07 16:21 Pgina 13 COMMAND WITH BASIC FUNCTIONS A On/Off sensor. B Power sensors and displays between 0 and P. A B C D D Safety sensor and display. OPERATION SWITCHING ON A HOB The operation is the same as described for the commands with special functions. TIMER OPERATION The operation is the same as described for the commands with special functions. ACOUSTIC SIGNAL The operation is the same as described for the commands with special functions. FUNCTION (P point) (Fast heating function) This function allows greater power to be obtained during a certain time. The "P. " function (P point) is obtained by pressing the "+" button as far as the "P. " position, release the command and the "P. " will flash, press the command again and it will be put in the maximum power "P. " position (P point) then press the "-" command and enter in the chosen cooking time. [. . . ] When switching the hob plate on for the first time or after a long time without use, a code will light up on the command panel. 20 Live Brown Blue Blue Brown C60T376A8. qxd 14/3/07 16:21 Pgina 21 TROUBLESHOOTING YOU FIND THAT The induction plate does not work. Trip switches are activated when you switch it on. When you connect the appliance to the network a light appears. [. . . ]