User manual FANUC 15 – MODEL B OPERATION FOR MACHINING CENTER

[. . . ] GE Fanuc Automation Computer Numerical Control Products Series 15 / 150 ­ Model B for Machining Center Operator's Manual (Operation) GFZ-62564E-1/02 December 1996 GFL-001 Warnings, Cautions, and Notes as Used in this Publication Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. [. . . ] 8 When all the values and names of common variables have been output, the operation selection soft keys are displayed again. Function selection keys on a 9-inch CRT display 1, 2 SETTING SERVICE MESSAGE CHAPTER Chapter selection keys displayed by pressing SETTING on a 9-inch CRT display 2 HANDY GENERAL MACRO Operation selection keys displayed by pressing MACRO on a 9-inch CRT display 3, 4 PANCH ­ 220 ­ B­62564E­1/02 10. SETTING AND DISPLAYING DATA Operation guidance keys (PUNCH) on a 9-inch CRT display 5 COMMON2 (FILE#) 6, 7 STOP NOFEED Function selection keys on the 14-inch CRT display 1, 2 POSI PRO TION GRAM OFF SET PRO GRAM CHECK SET TING SER VICE MES SAGE CHAP TER Chapter selection keys displayed by pressing SETTING on the 14-inch CRT display 2 HAN DY GEN ERAL MACRO VAR. TIME CHAP TER Operation selection keys displayed by pressing MACRO on the 14-inch CRT display 3, 4 IN PUT IN ALL INPUT NUM PUT+ CLEAR EMPTY BER INPUT PUN CH CHAP TER Operation guidance keys (PUNCH) on the 14-inch CRT display 5 COM MON NONVOL (FILE #) 6, 7 STOP NO FEED The values and names of the common variables can be output in any mode as long as automatic operation is in the stopped state. When the values and names of the common variables are output to a FANUC floppy disk, the file name in the file list is COMMON. NONVOL. (2) Inputting the values and names of common variables Input the values and names of the common variables using one of the following methods: (i) The output of the values and names of common variables is read as a program in the edit mode, then the program is executed in the memory mode. 1 Before registering the program in memory, perform steps (1) to (6). (2) Display the program screen using the soft keys. (3) Press the operation menu key to display the READ soft key. (5) Press (FILE#), and enter the file number. (Search for the file storing the program was output to the FANUC disk. ) (6) Press (PROG#), enter a program number, then press EXEC. The program number can be any number that is not currently being used. ­ 221 ­ 10. SETTING AND DISPLAYING DATA B­62564E­1/02 2 After the above input operation is completed, the program created by outputting the values and names of the common variables is displayed on the screen. Press the cycle start button to execute the program. The values and names of the common variables are then input to the custom macro memory area in the CNC. 4 Select the screen for displaying custom macro variable data. Check the display to ensure that the values and names of the common variables are set properly. (ii) The program created by outputting the values and names of the common variables is executed in tape mode to directly input the values and names. 1 Set the program tape in the tape reader. The common variables and names are input to the custom macro memory area in the CNC. 4 Select the screen for displaying custom macro variable data. Check the display to ensure that the values and names of the common variables are set properly. NOTE 1 If the write protect function (parameters 7031 and 7032) is enabled for common variables, release the protection before inputting the values and names of the common variables. [. . . ] The parameter for selecting the graphic display axis (parameter No. Another user (such as the PC) tried to use the graphic CPU. Workpiece zero point manual setting was performed on the external workpiece zero point offset. The tool has attempted to enter an area set as inhibited by stored stroke limit 1 during manual movement in the positive direction. [. . . ]