User manual FBII OMNI-848EU

[. . . ] +DUGZLUHG:LUHOHVV6\VWHP 201, 201, (8 201, 201, (8 8VHU*XLGH ARMED READY STAY 1 4 7 2 5 8 0 3 6 9 # BYPASS INSTANT ARMED READY STAY 1 4 7 2 5 8 0 3 6 9 # ARM AC / LB 1 4 7 2 5 8 0 3 6 9 # INSTANT CODE BYPASS INSTANT READY CODE STAY BYPASS STAY INST LO BATT SPRV. CODE FIRE BURGLARY INSTRUMENTS, INC. N9939V2 4/01 Table Of Contents QUICK REFERENCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SYSTEM REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ARMING THE SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The system exits this mode when the star [D] key is pressed. - 19 - Miscellaneous Commands (cont) ON-LINE DOWNLOAD If enabled by your system installer, an on-line download allows you to initiate a remote communications session with the Central Station (CS) Downloading computer from the control panel location. Typically, the CS initiates a remote communications session. On-line Downloading allows you to call the office (from the same telephone line as the panel), discuss the action required, and allow the CS operator to complete the request while on-line; no additional telephone call is needed. Note that the office number that is dialed should be the phone line that the downloading computer is attached to. On-line connection can be made as follows: 1. Uses the home telephone to dial the CS Downloading modem telephone line. Connection is made with a person at the CS Downloading computer and the account to be downloaded will be verbally identified. This will cause the control panel to react as if it received a request for a remote communications session, and to look for the standard panel-to-CS protocol. Once the standard connection is made, the necessary remote communications sessions can take place (upload, download, remote commands). Hang up the telephone to prevent interference that may affect upload/download data. The downloader software will automatically terminate the connection after remote communications end. - 20 - Using a Pager If programmed, the system can send messages to a pager. The messages are displayed as follows: ACCT E XXX where: "ACCT" = the 4-digit central station no. 1 account number set by your system installer. We suggest that you obtain the number from your system installer and record it here. There are 4 event types: alarms, troubles, openings, and closings. These event codes are as follows: Openings = 0, Closings = 1, Alarm or Trouble = 9 the zone or user designation, depending on the event "E" = "XXX" = If multiple events occur, the signal for the highest-priority event is sent first. Events ranked from highest to lowest priority are alarm, trouble, open, and close. CHANGING THE PAGER PHONE NUMBER (FOLLOW-ME) You can change your pager follow-me phone number as follows if your installer enabled this feature: 1. Access pager number programming by pressing the following keys in sequence: [#], [5], and [8]. An acknowledgement tone sounds to indicate pager number programming has been accessed. The # , 5 , 8 command is accessible only while the system is disarmed and the dialer, dialer delay, and bell are not active. In pager phone number programming mode, only the LCD keypad provides visual display of the numbers already programmed or numbers that are being changed. [. . . ] However, even if the system responds to the emergency as intended, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 20 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. [. . . ]