User manual FELLOWES DS-12CI

[. . . ] Fellowes shredders are built stronger, engineered to run longer, resist jams and power through large jobs. The Fellowes worry free warranty described below covers the performance of the product, provides for prompt service and support, plus a lifetime cutter warranty. ("Fellowes") warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 2 years from the date of purchase by the original consumer. [. . . ] 1* Paper entry width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9"/230mm *8. 5"x11", 20lb. , (75g) paper at 120V, 60 Hz, 4Amps; heavier paper, humidity or other than rated voltage may reduce capacity. Recommended daily usage rates: 25­50 shredding passes per day, 25 credit cards; 10 CDs. 12 sheets per pass. Fellowes SafeSense® shredders are designed to be operated in home and office environments ranging between 50 ­ 80 degrees Fahrenheit (10 ­ 26 degrees Celsius) and 40 ­ 80% relative humidity. ADVANCED PRODUCT FEATURES Jam Proof System Eliminates frustrating jams by preventing overloads and powering through misfed paper. TECHNICAL EXPLANATION Sheet capacity indicator tells you when you have too many sheets or too few to maximize productivity AUTO Patented SafeSense® Technology Stops shredder immediately when hands are too close to the paper entry. TECHNICAL EXPLANATION 12 SilentShredTM Technology SilentShredTM noise quality shreds without noisy disruptions. TECHNICAL EXPLANATION SilentShredTM motor features whisper-quiet, efficient shredding performance without the noisy disruptions F. O O. AUTO AUTO Shredder will stop automatically and indicator will light up when hands are too close to the paper entry AUTO Shredder will not operate when too many sheets are fed into paper entry (red light). Reduce sheet quantity and refeed If misfed, shredder will automatically adjust to power through or reverse out paper AUTO 12 Shredder will resume normal operation when hands are no longer near the paper entry AUTO Flashing indicator warns when SafeSense® technology has been shut off AUTO 12 P. AUTO IMPORTANT SAFETY INSTRUCTIONS -- Read Before Using! · Keep away from children and pets. Always set to off or unplug when not in use. · Keep foreign objects ­ gloves, jewelry, clothing, hair, etc. If object enters top opening, switch to Reverse ( ) to back out object. · Never use aerosol products, petroleum based lubricants or other flammable products on or near shredder. · Do not use if damaged or defective. Do not place near or over heat source or water. · This shredder has a Disconnect Power Switch (G) that must be in the ON (I) position to operate shredder. In case of emergency, move switch to OFF (O) position. [. . . ] If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin. CLEANING AUTO-START INFRARED SENSORS Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry). TO CLEAN THE SENSORS ADVANCED PRODUCT FEATURE MAINTENANCE AND TROUBLESHOOTING JAM PROOF SYSTEM* Eliminates frustrating jams by preventing overloads and powering through misfed paper. DISABLING THE FEATURE 1 2 12 3 4 12 AUTO AUTO AUTO 1 12 AUTO 2 3 12 3 4 3 5 12 Turn off and unplug shredder Lift CD flap Locate Auto-start infared sensor Dip cotton swab in rubbing alcohol Using cotton swab, wipe away any contamination from the paper sensors AUTO AUTO PREVENTIVE MAINTENANCE AND MISCELLANEOUS TROUBLESHOOTING · Run shredder once a day in reverse for 15 seconds to clear cutters · Empty wastebasket when bin full indicator light is illuminated using bag # 36052 · Shredder will not function if the pull-out bin is not pushed all the way in, or if bin needs to be emptied. [. . . ]